- 您現在的位置：買賣IC網 > PDF目錄9017 > AD5601BKSZ-REEL7 (Analog Devices Inc)IC DAC 8BIT BUFF V-OUT SC70-6 PDF資料下載
參數資料
| 型號： | AD5601BKSZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 8BIT BUFF V-OUT SC70-6 |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1 |
| 系列： | nanoDAC™ |
| 設置時間： | 6µs |
| 位數： | 8 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 500µW |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-TSSOP，SC-88，SOT-363 |
| 供應商設備封裝： | SC-70-6 |
| 包裝： | 標準包裝 |
| 輸出數目和類型： | 1 電壓，單極；1 電壓，雙極 |
| 產品目錄頁面： | 783 (CN2011-ZH PDF) |
| 其它名稱： | AD5601BKSZ-REEL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
Data Sheet
AD5601/AD5611/AD5621
Rev. G | Page 19 of 24
USING THE AD5601/AD5611/AD5621 WITH A
GALVANICALLY ISOLATED INTERFACE
In process control applications in industrial environments,
it is often necessary to use a galvanically isolated interface to
protect and isolate the controlling circuitry from any hazardous
common-mode voltages that might occur in the area where the
DAC is functioning. iCoupler provides isolation in excess of
2.5 kV. Because the AD5601/AD5611/AD5621 use a 3-wire serial
logic interface, the ADuM1300 3-channel digital isolator
provides the required isolation (see Figure 53). The power
supply to the part also needs to be isolated, which is done by
using a transformer. On the DAC side of the transformer, a 5 V
regulator provides the 5 V supply required for the AD5601/
AD5611/AD5621.
Figure 53. AD5601/AD5611/AD5621 with a Galvanically Isolated Interface
POWER SUPPLY BYPASSING AND GROUNDING
When accuracy is important in a circuit, it is helpful to carefully
consider the power supply and ground return layout on the
board. The PCB containing the AD5601/AD5611/AD5621
should have separate analog and digital sections, each having its
own area of the board. If the AD5601/AD5611/AD5621 are in a
system where other devices require an AGND-to-DGND
connection, the connection should be made at one point only.
This ground point should be as close as possible to the
AD5601/AD5611/AD5621.
The power supply to the AD5601/AD5611/AD5621 should be
bypassed with 10 F and 0.1 F capacitors. The capacitors
should be physically as close as possible to the device, with the
0.1 F capacitor ideally right up against the device. The 10 F
capacitors are the tantalum bead type. It is important that the
0.1 F capacitor have low effective series resistance (ESR) and
effective series inductance (ESI), such as in common ceramic
types of capacitors. This 0.1 F capacitor provides a low imped-
ance path to ground for high frequencies caused by transient
currents due to internal logic switching.
The power supply line itself should have as large a trace as
possible to provide a low impedance path and reduce glitch
effects on the supply line. Clocks and other fast switching
digital signals should be shielded from other parts of the board
by digital ground. Avoid crossover of digital and analog signals,
if possible. When traces cross on opposite sides of the board,
ensure that they run at right angles to each other to reduce
feedthrough effects on the board. The best board layout tech-
nique is the microstrip technique, where the component side of
the board is dedicated to the ground plane only and the signal
traces are placed on the solder side. However, this is not always
possible with a two-layer board.
06853-
052
VDD
AD5601/
AD5611/
AD5621
ADuM1300
POWER
10F
0.1F
GND
5V
REGULATOR
SCLK
VOA
VOUT
VOB
SYNC
VOC
VIA
VIB
VIC
SCLK
SDI
DATA
SDIN
相關PDF資料 |
PDF描述 |
|---|---|
| MS27513E22A2S | CONN RCPT 85POS BOX MNT W/SCKT |
| D38999/20JH55SB | CONN RCPT 55POS WALL MNT W/SCKT |
| VI-234-MW-F4 | CONVERTER MOD DC/DC 48V 100W |
| MS3122E20-16P | CONN RCPT 16POS BOX MNT W/PINS |
| GTC030G-32-1P | CONN RCPT 5POS PANEL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5602 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 V to 5.5 V, <100 uA, 8-/10-/12-Bit nanoDACs with |
| AD5602BCPZ-2-RL7 | 制造商:Analog Devices 功能描述:SINGLE 2.7-5.5V 8BIT I2C DAC IN SC-70 - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 8BIT I2C SC70-6 制造商:Analog Devices 功能描述:Digital to Analog Converters - DAC SGL 2.7-5.5V 8B I2C |
| AD5602BKSZ-2500RL7 | 功能描述:IC DAC 8BIT SGL SUPPLY LV SC70-6 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5602BKSZ-2REEL7 | 功能描述:IC DAC 8BIT SGL SUPPLY LV SC70-6 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 設計資源:Unipolar, Precision DC Digital-to-Analog Conversion using AD5450/1/2/3 8-14-Bit DACs (CN0052) Precision, Bipolar, Configuration for AD5450/1/2/3 8-14bit Multiplying DACs (CN0053) AC Signal Processing Using AD5450/1/2/3 Current Output DACs (CN0054) Programmable Gain Element Using AD5450/1/2/3 Current Output DAC Family (CN0055) Single Supply Low Noise LED Current Source Driver Using a Current Output DAC in the Reverse Mode (CN0139) 標準包裝:10,000 系列:- 設置時間:- 位數:12 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 薄型，TSOT-23-8 供應商設備封裝:TSOT-23-8 包裝:帶卷 (TR) 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:2.7M |
| AD5602YKSZ-1 | 制造商:Analog Devices 功能描述:DAC SGL RES-STRING 8BIT 6PIN SC-70 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。