參數資料
型號： AD5392BSTZ-5
廠商： Analog Devices Inc
文件頁數： 29/44頁
文件大小： 0K
描述： IC DAC 14BIT 8CHAN 3V 52LQFP
產品培訓模塊： Data Converter Fundamentals
DAC Architectures
產品變化通告： AD5390/1/2 Redesign Change 16/May/2012
設計資源： 8 to 16 Channels of Programmable Voltage with Excellent Temperature Drift Performance Using AD5390/1/2 (CN0029)
AD5390/91/92 Channel Monitor Function (CN0030)
標準包裝： 1
設置時間： 8µs
位數： 14
數據接口： I²C，串行
轉換器數目： 16
電壓電源： 單電源
功率耗散（最大）： 35mW
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 52-LQFP
供應商設備封裝： 52-LQFP（10x10）
包裝： 托盤
輸出數目和類型： 8 電壓，單極
采樣率（每秒）： 125k
Data Sheet
AD5390/AD5391/AD5392
Rev. E | Page 35 of 44
HARDWARE FUNCTIONS
RESET FUNCTION
Bringing the RESET line low resets the contents of all internal
registers to their power-on reset state. RESET is a negative edge-
sensitive input. The default corresponds to m at full scale and
c at zero scale. The contents of all DAC registers are cleared by
setting the outputs to 0 V. This sequence takes 270 s maximum.
The falling edge of RESET initiates the reset process. BUSY goes
low for the duration, returning high when RESET is complete.
While BUSY is low, all interfaces are disabled and all LDAC
pulses are ignored. When BUSY returns high, the part resumes
normal operation, and the status of the RESET pin is ignored
until the next falling edge is detected.
ASYNCHRONOUS CLEAR FUNCTION
CLR is negative-edge-triggered and BUSY goes low for the
duration of the CLR execution. Bringing the CLR line low
clears the contents of the DAC registers to the data contained in
the user-configurable CLR register and sets the analog outputs
accordingly. This function can be used in system calibration
to load zero scale and full scale to all channels together. The
execution time for a CLR is 20 s on the AD5390/AD5391 and
15 s on the AD5392.
BUSY AND LDAC FUNCTIONS
BUSY is a digital CMOS output indicating the status of the
AD539x devices. BUSY goes low during internal calculations
of x2 data. If LDAC is taken low while BUSY is low, this event
is stored. The user can hold the LDAC input permanently low
and, in this case, the DAC outputs update immediately
after BUSY goes high. BUSY also goes low during a power-on
reset and when a falling edge is detected on the RESET pin.
During this time, all interfaces are disabled and any events
on LDAC
are ignored.
The AD539x products contain an extra feature whereby a DAC
register is not updated unless its x2 register has been written
to since the last time LDAC was brought low. Normally,
when LDAC is brought low, the DAC registers are filled with
the contents of the x2 registers. However, these devices update
the DAC register only if the x2 data has changed, thereby
removing unnecessary digital crosstalk.
POWER-ON RESET
The AD539x products contain a power-on reset generator
and state machine. The power-on reset resets all registers to a
predefined state, and the analog outputs are configured as high
impedance outputs. The BUSY pin goes low during the power-
on reset sequence, preventing data writes to the device.
POWER-DOWN
The AD539x products contain a global power-down feature that
puts all channels into a low power mode, reducing the analog
power consumption to 1 A maximum and the digital power
consumption to 20 A maximum. In power-down mode, the
output amplifier can be configured as a high impedance output
or to provide a 100 k load to ground. The contents of all
internal registers are retained in power-down mode. When
exiting power-down, the settling time of the amplifier elapses
before the outputs settle to their correct value.
MICROPROCESSOR INTERFACING
AD539x to MC68HC11
The serial peripheral interface (SPI) on the MC68HC11 is
configured for master mode (MSTR = 1), clock polarity bit
(CPOL) = 0, and the clock phase bit (CPHA) = 1. The SPI is
configured by writing to the SPI control register (SPCR)—see
the 68HC11 User Manual. SCK of the MC68HC11 drives the
SCLK of the AD539x, the MOSI output drives the serial data
line (DIN) of the AD539x, and the MISO input is driven from
DOUT. The SYNC signal is derived from a port line (PC7). When
data is being transmitted to the AD539x, the SYNC line is taken
low (PC7). Data appearing on the MOSI output is valid on the
falling edge of SCK. Serial data from the MC8HC11 is trans-
mitted in 8-bit bytes with only eight falling clock edges
occurring in the transmit cycle.
DVDD
MC68HC11
SDO
DIN
AD539x
SCLK
RESET
SYNC
MISO
MOSI
SCK
PC7
SPI/I2C
03773-
026
Figure 37. AD539x-MC68HC11 Interface
相關PDF資料
PDF描述
MS27473T20B35PLC CONN HSG PLUG 79POS STRGHT PIN
VE-2WP-MY-F1 CONVERTER MOD DC/DC 13.8V 50W
AD669ARZ IC DAC 16BIT MONO W/VREF 28-SOIC
VI-BW0-MV-F2 CONVERTER MOD DC/DC 5V 150W
MS27496E23F53S CONN RCPT 53POS BOX MNT W/SCKT
相關代理商/技術參數
參數描述
AD5398ABCBZ-REEL 功能描述:IC DAC 10BIT CURRENT-SINK 9WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 設計資源:Unipolar, Precision DC Digital-to-Analog Conversion using AD5450/1/2/3 8-14-Bit DACs (CN0052) Precision, Bipolar, Configuration for AD5450/1/2/3 8-14bit Multiplying DACs (CN0053) AC Signal Processing Using AD5450/1/2/3 Current Output DACs (CN0054) Programmable Gain Element Using AD5450/1/2/3 Current Output DAC Family (CN0055) Single Supply Low Noise LED Current Source Driver Using a Current Output DAC in the Reverse Mode (CN0139) 標準包裝:10,000 系列:- 設置時間:- 位數:12 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 薄型，TSOT-23-8 供應商設備封裝:TSOT-23-8 包裝:帶卷 (TR) 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:2.7M
AD5398ABCBZ-REEL7 功能描述:IC DAC 10BIT CURRENT-SINK 9WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF)
AD5398A-WAFER 功能描述:10 Bit Digital to Analog Converter 1 9-WLCSP (1.52 x 1.69) 制造商:analog devices inc. 系列:- 包裝:散裝 零件狀態:上次購買時間 位數:10 數模轉換器數:1 建立時間:250μs（標準） 輸出類型:Current - Unbuffered 差分輸出:無 數據接口:I2C 參考類型:內部 電壓 - 電源，模擬:2.7 V ~ 5.5 V 電壓 - 電源，數字:2.7 V ~ 5.5 V INL/DNL（LSB）:±1.5，±1（最大） 架構:電流阱 工作溫度:-30°C ~ 85°C 封裝/外殼:9-UFBGA，WLCSP 供應商器件封裝:9-WLCSP（1.52 x 1.69） 標準包裝:1
AD5398BCBZ-REEL 功能描述:IC DAC 10BIT CURRENT-SINK 9WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:*
AD5398BCBZ-REEL7 功能描述:IC DAC 10BIT CURRENT-SINK 9WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*