- 您現在的位置：買賣IC網 > PDF目錄9001 > AD5061BRJZ-2REEL7 (Analog Devices Inc)IC DAC 16BIT SPI/SRL SOT23-8 PDF資料下載
參數資料
| 型號： | AD5061BRJZ-2REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT SPI/SRL SOT23-8 |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1 |
| 系列： | nanoDAC™ |
| 設置時間： | 4µs |
| 位數： | 16 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 6mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-8 |
| 供應商設備封裝： | SOT-23-8 |
| 包裝： | 標準包裝 |
| 輸出數目和類型： | 1 電壓，單極；1 電壓，雙極 |
| 采樣率（每秒）： | 1.3M |
| 產品目錄頁面： | 781 (CN2011-ZH PDF) |
| 其它名稱： | AD5061BRJZ-2REEL7DKR |
AD5061
Rev. B | Page 18 of 20
APPLICATIONS
CHOOSING A REFERENCE
To achieve the optimum performance from the AD5061,
thought should be given to the choice of a precision voltage
reference. The AD5061 has just one reference input, VREF. The
voltage on the reference input is used to supply the positive
input to the DAC. Therefore, any error in the reference is
reflected in the DAC.
There are four possible sources of error when choosing a vol-
tage reference for high accuracy applications: initial accuracy,
ppm drift, long-term drift, and output voltage noise. Initial
accuracy on the output voltage of the DAC leads to a full-scale
error in the DAC. To minimize these errors, a reference with
high initial accuracy is preferred. Also, choosing a reference
with an output trim adjustment, such as the ADR43x family,
allows a system designer to trim out system errors by setting a
reference voltage to a voltage other than the nominal. The trim
adjustment can also be used at the operating temperature to
trim out any errors.
Because the supply current required by the AD5061 is
extremely low, the parts are ideal for low supply applications.
The ADR395 voltage reference is recommended. This requires
less than 100 μA of quiescent current and can, therefore, drive
multiple DACs in one system, if required. It also provides very
good noise performance at 8 μV p-p in the 0.1 Hz to 10 Hz range.
AD5061
SYNC
SCLK
DIN
7V
5V
VOUT = 0V TO 5V
ADR395
04
76
2-
0
36
3-WIRE
SERIAL
INTERFACE
Figure 46. ADR395 as Reference to the AD5061
Long-term drift is a measure of how much the reference drifts
over time. A reference with a tight long-term drift specification
ensures that the overall solution remains relatively stable during
its entire lifetime. The temperature coefficient of a reference’s
output voltage affects INL, DNL, and TUE. A reference with a
tight temperature coefficient specification should be chosen to
reduce temperature dependence of the DAC output voltage on
ambient conditions.
In high accuracy applications, which have a relatively low noise
budget, reference output voltage noise needs to be considered. It
is important to choose a reference with as low an output noise
voltage as practical for the system noise resolution required.
Precision voltage references, such as the ADR435, produce low
output noise in the 0.1 Hz to 10 Hz region.
Table 7 shows examples of recommended precision references
for use as a supply to the AD5061.
Table 7. Precision References Part List for the AD5061
Part No.
Initial
Accuracy
(mV max)
Temperature Drift
(ppm/°C max)
0.1 Hz to
10 Hz Noise
(μV p-p typ)
ADR435
±2
3 (SO-8)
8
ADR425
±2
3 (SO-8)
3.4
ADR02
±3
3 (SO-8)
10
ADR02
±3
3 (SC70)
10
ADR395
±5
9 (TSOT-23)
8
BIPOLAR OPERATION
The AD5061 has been designed for single-supply operation, but
a bipolar output range is also possible using the circuit shown in
Figure 47. The circuit shown yields an output voltage range of
±5 V. Rail-to-rail operation at the amplifier output is achievable
using an AD8675/AD820/AD8032 or an OP196/OP295.
The output voltage for any input code can be calculated as
follows:
×
+
×
×
=
1
R
2
R
V
1
R
2
R
1
R
D
V
DD
O
65536
where D represents the input code in decimal (0 to 65536).
With VREF = 5 V, R1 = R2 = 10 kΩ,
V
5
65536
10
×
=
D
V
O
This is an output voltage range of ±5 V with 0x0000 correspond-
ing to a 5 V output and 0xFFFF corresponding to a +5 V output.
AD5061
+5V
10F
04
76
2-
03
7
R1 = 10k
VBF
VOUT
VREF
0.1F
3-WIRE
SERIAL
INTERFACE
AD820/
OP295
+
–
–5V
+5V
R2 = 10k
±5V
Figure 47. Bipolar Operation with the AD5061
相關PDF資料 |
PDF描述 |
|---|---|
| ICS581G-01LF | IC CLK MUX ZD GLITCHFREE 16TSSOP |
| VI-J5V-MZ-F4 | CONVERTER MOD DC/DC 5.8V 25W |
| LTC2621CDD#PBF | IC DAC 12BIT SGL R-R VOUT 10DFN |
| AD5424YRUZ | IC DAC 8BIT MULTIPLYING 16-TSSOP |
| IDT23S08E-1HPGI | IC CLK MULT PLL HI DRV 16-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5061BRJZ-3 | 制造商:Analog Devices 功能描述:DAC SGL R-2R 16BIT 8PIN SOT-23 - Bulk |
| AD5061YRJZ-1 | 制造商:Analog Devices 功能描述:DAC SGL R-2R 16BIT 8PIN SOT-23 - Bulk |
| AD5061YRJZ-1500RL7 | 功能描述:IC DAC 16BIT SPI/SRL SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5061YRJZ-1REEL7 | 功能描述:IC DAC 16BIT SPI/SRL SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5062 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
發(fā)布緊急采購，3分鐘左右您將得到回復。