- 您現在的位置：買賣IC網 > PDF目錄9470 > AD2S44-TM12B (Analog Devices Inc)IC CONV SYNC/R-D 14BIT 2CH 32DIP PDF資料下載
參數資料
| 型號： | AD2S44-TM12B |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONV SYNC/R-D 14BIT 2CH 32DIP |
| 標準包裝： | 1 |
| 類型： | R/D 轉換器 |
| 分辨率（位）： | 14 b |
| 數據接口： | 并聯 |
| 電壓電源： | 雙 ± |
| 電源電壓： | ±15V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 32-CDIP（0.900"，22.86mm） |
| 供應商設備封裝： | 32-CDIP 底部銅焊 |
| 包裝： | 管件 |
| 其它名稱： | AD2S44TM12B AD2S44TM12B-ND |
Data Sheet
AD2S44
Rev. B | Page 7 of 12
THEORY OF OPERATION
The AD2S44 operates on a tracking principle. The output digital
word continually tracks the position of the synchro/resolver
shaft without the need for external convert commands and
status wait loops. As the transducer moves through a position
equivalent to the least significant bit weighting, the output
digital word is updated.
Each channel is identical in operation, sharing power supply
and output pins. Both channels operate continuously and
independently of each other. The digital output from either
channel is available after switching the channel select and
output enable inputs.
If the device is a synchro-to-digital converter, the 3-wire synchro
output is connected to the S1, S2, and S3 pins on the unit, and
a solid-state Scott T input conditioner converts these signals into
resolver format given by
V1 = K E0 sin ωt sin θ
V2 = K E0 sin ωt cos θ
where:
θ is the angle of the synchro shaft.
E0 sin ωt is the reference signal.
K is the transformation ratio of the input signal conditioner.
If the unit is a resolver-to-digital converter, the 4-wire resolver
output is connected directly to the S1, S2, S3, and S4 pins on
the unit.
To understand the conversion process, assume that the current
word state of the up-down counter is . V1 is multiplied by cos ,
and V2 is multiplied by sin to give the following:
K E0 sin ωt sin θ cos
K E0 sin ωt cos θ sin
These signals are subtracted by the error amplifier to give
K E0 sin ωt (sin θ cos cos θ sin )
or
K E0 sin ωt sin (θ )
A phase sensitive detector, integrator, and voltage-controlled
oscillator (VCO) form a closed-loop system that seeks to null sin
(θ ). When this is accomplished, the word state of the up-down
counter () equals the synchro/resolver shaft angle (θ), to within
the rated accuracy of the converter.
CONNECTING THE CONVERTER
The power supply voltages connected to VS and +VS are to be
±15 V and cannot be reversed.
It is suggested that a parallel combination of a ceramic 100 nF
capacitor and a tantalum 6.8 F capacitor be placed from each
of the supply pins to GND.
The pin marked GND is connected electrically to the case and
is to be taken to 0 V potential in the system.
The digital output is taken from Pin 26 to Pin 32 and from Pin 1
to Pin 7. Pin 26 is the MSB, and Pin 7 is the LSB.
The reference connections are made to the RHI pins and the RLO
pins. In the case of a synchro, the signals are connected to the
S1, S2, and S3 pins, according to the following convention:
ES1S3 = ERLORHIsin ωt sin θ
ES3S2 = ERLORHIsin ωt sin (θ 120°)
ES2S1 = ERLORHIsin ωt sin (θ – 240°)
For a resolver, the signals are connected to the S1, S2, S3, and S4
pins, according to the following convention:
ES1S3 = ERLORHIsin ωt sin θ
ES2S4 = ERLORHIsin ωt cos θ
CHANNEL SELECT (A/B)
A/B is the channel select input. A Logic 1 selects Channel A, and
a Logic 0 selects Channel B. Data becomes valid 640 ns after A/B
is toggled. Timing information is shown in Figure 4 and Figure 5.
AD2S44
REFERENCE
CONDITIONER
SYNCHRO/
RESOLVER
CONDITIONER
PHASE-
SENSITIVE
DETECTOR
THREE-
STATE
OUTPUT
LATCHES
DB1 (MSB)
TO
DB14 (LSB)
PHASE-
SENSITIVE
DETECTOR
HIGH
SPEED
SIN/COS
MULTIPLIER
V1
V2
BUILT-IN
TEST
DETECTION
ERROR
AMP
UP-DOWN
COUNTER
UP-DOWN
COUNTER
INTEGRATOR
VCO
INTEGRATOR
ERROR
AMP
HIGH
SPEED
SIN/COS
MULTIPLIER
SYNCHRO/
RESOLVER
CONDITIONER
REFERENCE
CONDITIONER
S3 (A)
RHI (A)
RLO (A)
RHI (B)
RLO (B)
+VS
–VS
GND
S4 (A)
S1 (A)
S2 (A)
S3 (B)
S4 (B)
S1 (B)
S2 (B)
OE
A/B
BIT
02947-
010
Figure 3. Functional Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| LTC6990IDCB#TRMPBF | IC OSC SILICON 1MHZ 6DFN |
| LTC1799CS5#TRPBF | IC OSC SILICON 33MHZ TSOT23-5 |
| AD2S44-TM11B | IC SYNC-R/D CONV 14BIT 2CH 32DIP |
| MS27466T25F35PB | CONN RCPT 128POS WALL MNT W/PINS |
| MS27466E25F35PB | CONN RCPT 128POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S44TM13B | 制造商:Analog Devices 功能描述:LOW COST 14BIT DUAL CH SYNCHRO/RESOLVER-TO-DGTL CNVRTR 32SB - Bulk 制造商:Rochester Electronics LLC 功能描述:HI-REL 11.8VREF 11.8VRES - Bulk |
| AD2S44TM14B | 制造商:Analog Devices 功能描述:LOW COST 14BIT DUAL CH SYNCHRO/RESOLVER-TO-DGTL CNVRTR 32SB - Bulk 制造商:Rochester Electronics LLC 功能描述:HI-REL 26VREF 26VRES IC - Bulk |
| AD2S44TM18 | 制造商:Rochester Electronics LLC 功能描述:4.0ARC MIN 11.8VREF 26VRE - Bulk |
| AD2S44TM18B | 制造商:Analog Devices 功能描述:HI-REL 11.8VREF 26VRES IC - Bulk |
| AD2S44-TM18B | 功能描述:IC CONV SYNC/R-D 14BIT 2CH 32DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。