參數資料
型號: ACPM-7813-BLK
英文描述: CDMA/AMPS Power Amplifier Module
中文描述: 碼分多址/ AMPS二元功率放大器模塊
文件頁數: 19/21頁
文件大?。?/td> 183K
代理商: ACPM-7813-BLK
19
2) Circuit Operation
The design of the power module
(PAM) provide bias control via
Vcntl to achieve optimal RF
performance and power control.
The control pin is labeled Vref
(Vcntl). Please refer to Figure 26
for the block diagram of this
PAM.
Typical Operation Conditions
(Vdd1=Vdd2=Vbias = 3.0V)
Parameter
ACPM-7813
Frequency Range
824 – 849 MHz
Output Power
28.5 dBm
Vcntl
2.5 V
3) Maximum Ratings
Vdd
5.0V
Drain Current
1.5A
Vcntl
3V
RF input
10 dBm
Temperature
-30 to 85
°
C
Please Note: Avoid Electrostatic Discharge
on all I/O’s.
4) Heat Sinking
The demonstration PC Board
provides an adequate heat sink.
Maximum device dissipation
should be kept below 2.5 Watts.
5) Testing
- Signal Source
The CDMA modulated signal for
the test is generated using an
Agilent ESG-D4000A (or ESG-
D3000A) Digital Signal Generator
with the following settings:
CDMA Setup : Reverse
Spreading: On
Bits/Symbol: 1
Data: PN15
Modulation: OQPSK
Chip Rate: 1.2288 Mcps
High Crest: On
Filter: Std
Phase Polarity: Invert
- ACPR Measurement
The ACPR (and channel power) is
measured using an Agilent 4406
VSA with corresponding ACPR
offsets for IS-98c and JSTD-8.
Averaging of 10 is used for ACPR
measurements.
- DC Connection
A DC Connector is provided to
allow ease of connection to the
I/O’s. Wires can be soldered to
the connector pins, or the
connector can be removed and
I/O’s contacted via clip leads or
direct soldered connections. The
wiring of I/O’s are listed in
Figure 1 through 3 and Pin
configuration table. The Vdd
sense connections are provided
to allow the use of remote-
sensing power supplies for
compensation of PCB traces and
cable resistance.
- Device Operation
1) Connect RF Input and Output
for the band under test.
2) Terminate all unused RF
ports into 50 Ohms.
3) Connect Vdd1 and Vdd2
supplies (including remote
sensing labeled Vdd1 S and
Vdd2 S on the board). Nomi-
nal voltage is 3.4V.
4)
Connect Vcntl supply and set
reference voltage to the
voltage shown in the data
packet. Note that the Vcntl pin
is on the back side of the
demonstration board. Please
limit Vcntl to not exceed the
corresponding listed “DC
Biasing Condition” in the Data
Packet. Note that increasing
Vcntl over the corresponding
listed “DC Biasing Condition”
can result in power decrease
and current can exceed the
rated limit.
5) Apply RF input power accord-
ing to the values listed in
“Operation Data” in Data
Packet.
6) Power down in opposite
sequence.
Figure 26. Power Module Block Diagram.
Input
Vdd1
Passive
Input
Match
On Chip
Inter-stage
Match
Bias Circuit
Passive
Output
Match
Vdd2
Output
Vcntl
Single control bias setting for low Idq
and 40% PAE at Pout = 28.5 dBm
Vbias
相關PDF資料
PDF描述
ACPM-7813-TR1 CDMA/AMPS Power Amplifier Module
ACS704ELC-015 Fully Integrated, Hall Effect-Based Linear Current Sensor with Voltage Isolation and a Low-Resistance Current Conductor
ACS704ELC-005 Fully Integrated, Hall Effect-Based Linear Current Sensor with Voltage Isolation and a Low-Resistance Current Conductor
ACS750LCA-075 CURRENT SENSOR ACS750 X CA -075
ACS750SCA-050 Current Sensor
相關代理商/技術參數
參數描述
ACPM-7813-TR1 功能描述:射頻放大器 CDMA Amp 824-849MHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
ACPM-7821 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz)
ACPM-7821-BLK 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz)
ACPM-7821-TR1 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz)
ACPM-7822 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:JCDMA 4x4 Power Amplifier Module (898-925MHz)