- 您現在的位置：買賣IC網 > PDF目錄375227 > ACF2101 Low Noise, Dual SWITCHED INTEGRATOR PDF資料下載
參數資料
| 型號： | ACF2101 |
| 英文描述： | Low Noise, Dual SWITCHED INTEGRATOR |
| 中文描述： | 低噪聲，雙交換式積分器 |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 192K |
| 代理商： | ACF2101 |
ACF2101
12
For C
INTEGRATION
= 100pF, R
PROGRAM
is calculated below:
At the end of the integration cycle, the Hold switch of the
ACF2101 is opened to hold a constant value at the output of
the ACF2101. The constant value output voltage of the
ACF2101 is transferred onto a 10nF capacitor by closing the
ACF2101’s Select switch. The Select switch is then opened
which holds the voltage on the 10nF capacitor during the
next integration cycle and creates a DC output. With this
operation, the Select switch of the ACF2101 and the 10nF
capacitor form a Sample/Hold (S/H) circuit. The OPA2107
is used to buffer the Sample/Hold output. The charge injec-
tion of the Select switch creates a small offset voltage, of
approximately 1mV in this example. The 10nF capacitor
was chosen as a large value to minimize this offset voltage.
After the Select switch opens, the ACF2101 is reset by
momentarily closing the Reset switch. The ACF2101’s Hold
switch is then closed to begin another integration cycle.
During the period of time that the Hold switch is open, the
input signal current is stored on the input capacitance of the
sensor (C
IN
). During this time, the input signal current
creates a voltage across the sensor. This voltage should be
kept below 500mV. When the Hold switch is closed, the
charge that has collected on C
IN
will be transferred to the
integration capacitor, C
INTEGRATION
, with no loss of signal.
Therefore, one integration cycle ends and the next integra-
tion cycle begins when the Hold switch is opened.
If 100% of signal acquisition is not required, or not wanted,
the Hold switch may be left closed, or the direct input to the
ACF2101 used. In this mode of operation, an integration
cycle ends when the Select switch is opened and the next
integration cycle begins when the Reset switch is opened.
Figure 11 shows a simple digital pattern generator which can
be used to create the timing signals to control the ACF2101
circuit of Figure 10. This circuit creates signals to control
the Select, Reset and Hold switches at a rate controlled by
the frequency of f
S
. Figure 9 shows the timing diagram
for these circuits.
In a sampled data system, the output of the ACF2101 at the
output of the Select switch can be converted to digital when
the ACF2101 is in the Hold mode. In this situation, of
course, the 10nF capacitor and the OPA2107 op amp are not
required.
f
S
R
PROGRAM
1M
10M
100M
167M
200M
1G
10kHz
1kHz
100Hz
60Hz
50Hz
10Hz
FIGURE 10. Programmable Current-to-Voltage Converter.
SENSOR
Hold
Reset
100pF
1/2
ACF2101
Select
V
I
C
10nF
IN
OUT
1/2
OPA2107
FIGURE 9. ACF2101 Current-to-Voltage Converter
Timing Diagram.
OUT
V
f
Integrator
output
See
Close-up
below
S
Hold
Rst
Select
Reset
Integrator
output
Current-to-Voltage converter timing diagram overview.
Expanded view of ACF2101 timing signals.
Hold
Hold
f
S
Transfer of
charge
from C
IN
Start/End
of integration cycle
相關PDF資料 |
PDF描述 |
|---|---|
| ACF2101BP | Low Noise, Dual SWITCHED INTEGRATOR |
| ACF2101BU | Low Noise, Dual SWITCHED INTEGRATOR |
| ACH16373DGG | JT 6C 6#12 PIN PLUG |
| ACH16373DL | 2.5V/3.3V 16-bit D-type transparent latch 3-State |
| ACH16374DGG | Circular Connector; MIL SPEC:MIL-DTL-38999 Series II; Body Material:Metal; Series:JT; No. of Contacts:13; Connector Shell Size:10; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ACF2101BP | 制造商:BB 制造商全稱:BB 功能描述:Low Noise, Dual SWITCHED INTEGRATOR |
| ACF2101BU | 功能描述:運算放大器 - 運放 Low Noise Dual Swtc Integrator RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| ACF2101BU | 制造商:Texas Instruments 功能描述:IC OP-AMP SW INT 2MHZ DUAL 24SOIC 制造商:Texas Instruments 功能描述:IC, OP-AMP SW INT 2MHZ DUAL 24SOIC 制造商:Texas Instruments 功能描述:IC, OP-AMP SW INT 2MHZ DUAL 24SOIC; Op Amp Type:Low Noise; No. of Amplifiers:2; Slew Rate:3V/s; Supply Voltage Range:4.5V to 18V, -10V to -18V; Amplifier Case Style:SOIC; No. of Pins:24; Bandwidth:2MHz; Operating Temperature ;RoHS Compliant: Yes |
| ACF2101BU | 制造商:Texas Instruments 功能描述:LOW NOISE DUAL SWITCHED INTEGRATOR INTE |
| ACF2101BU/1K | 功能描述:運算放大器 - 運放 Low Noise Dual Swtc Integrator RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。