- 您現在的位置：買賣IC網 > PDF目錄375222 > AAT3680 (Advanced Analogic Technologies, Inc.) Lithium-Ion Linear Battery Charge Controller PDF資料下載
參數資料
| 型號： | AAT3680 |
| 廠商： | Advanced Analogic Technologies, Inc. |
| 英文描述： | Lithium-Ion Linear Battery Charge Controller |
| 中文描述： | 鋰離子線性電池充電控制器 |
| 文件頁數： | 8/18頁 |
| 文件大小： | 265K |
| 代理商： | AAT3680 |
AAT3680
Lithium-Ion Linear Battery Charge Controller
8
3680.2003.4.0.91
High Speed Data Reporting
An optional system microcontroller interface can be
enabled by pulling the T2X pin up to 4.5V to 5.5V
during power-up sequence. The T2X pin should be
pulled high with the use of a 100k
resistor. If the
input supply to VP will not exceed 5.5V, then the
T2X pin may be tied directly to VP through a 100k
resistor. Since this is a TTL level circuit, it may not
be pulled higher than 5.5V without risk of damage
to the device.
When the high speed data report feature is enabled,
the STAT output periods are sped up to 40μs, mak-
ing the total status word 160μs in length. See Figure
3 below.
An additional feature is the Output Status for Battery
Not Detected state. When the AAT3680 senses there
is no battery connected to the BAT pin, the STAT pin
cycles for two periods, then remains off for two periods.
When in High Speed Data Reporting, the AAT3680
will only trickle charge at the 2x trickle charge level.
This is because the TX2 pin is pull high the enable
the high speed data reporting.
A status display LED may not be not be connected
to the STAT pin when the high speed data reporting
is being utilized. If both display modes are required,
the display LED must be switched out the circuit
before the T2X pin is pulled high. Failing to do so
could cause problems with the high speed switching
control circuits internal to the AAT3680.
Figure 3: Microcontroller Interface Logic Output
Sleep / Charge Complete
Temp., OC, OV Fault
Battery Conditioning
Constant Current Mode
Constant Voltage Mode
HI / HI / HI / HI
LO / LO / HI / HI
LO / LO / LO / LO
LO / HI / HI / HI
LO / LO / LO / HI
Charge Status
Output Status
STAT Level
Figure 2: LED Display Output
Sleep / Charge Complete
Temp., OC, OV Fault
Battery Conditioning
Constant Current Mode
Constant Voltage Mode
off / off / off / off
on / on / off / off
on / on / on / on
on / off / off / off
on / on / on / off
Charge Status
Output Status
LED Display
on/off
on/off
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
on/off
on/off
相關PDF資料 |
PDF描述 |
|---|---|
| AAT3680IKS-4.1-T1 | Lithium-Ion Linear Battery Charge Controller |
| AAT3680IKS-4.2-T1 | Lithium-Ion Linear Battery Charge Controller |
| AAT3680IKS-8.2-T1 | Lithium-Ion Linear Battery Charge Controller |
| AAT3680IKS-8.4-T1 | Lithium-Ion Linear Battery Charge Controller |
| AAT3680ITP-4.1-T1 | Lithium-Ion Linear Battery Charge Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT3680IKS-8.4-T1 | 制造商:Skyworks Solutions Inc 功能描述:AAT3680 Series 7 V Lithium-Ion/Polymer Linear Battery Charge Controller - MSOP-8 |
| AAT3681AIJS-4.1-5-T1 | 功能描述:電池管理 500mA USB Port/Adptr Li-Ion/Ply Batt Chgr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| AAT3681AIJS-4.1-T1 | 功能描述:電池管理 500mA USB Port/Adptr Li-Ion/Ply Batt Chgr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| AAT3681AIJS-4.2-1-T1 | 功能描述:IC BATT CHG LI-ION SC70JW-8 制造商:skyworks solutions inc. 系列:- 包裝:* 零件狀態:上次購買時間 電池化學:鋰離子/聚合物 電池數:1 電流 - 充電:恒流 - 可編程 可編程特性:- 故障保護:超溫，過壓，短路 充電電流 - 最大值:500mA 電池組電壓:4.2V 電壓 -?供電（最高）:7.5V 接口:USB 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:* 供應商器件封裝:* 標準包裝:1 |
| AAT3681AIJS-4.2-2-T1 | 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
發布緊急采購，3分鐘左右您將得到回復。