- 您現在的位置：買賣IC網 > PDF目錄375168 > AAT3221IGV-33-T1 (Advanced Analogic Technologies, Inc.) 150mA NanoPower⑩ LDO Linear Regulator PDF資料下載
參數資料
| 型號： | AAT3221IGV-33-T1 |
| 廠商： | Advanced Analogic Technologies, Inc. |
| 英文描述： | 150mA NanoPower⑩ LDO Linear Regulator |
| 中文描述： | 150mA的NanoPower⑩LDO線性穩壓器 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 390K |
| 代理商： | AAT3221IGV-33-T1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
AAT3221/2
150mA NanoPower LDO Linear Regulator
3221.200
2
.
03
.0.9
4
9
Applications Information
To assure the maximum possible performance is
obtained from the AAT3221/2, please refer to the
following application recommendations.
Input Capacitor
Typically a 1μF or larger capacitor is recommended
for C
IN
in most applications. A C
IN
capacitor is not
required for basic LDO regulator operation.
However, if the AAT3221/2 is physically located any
distance more than a centimeter or two from the
input power source, a C
IN
capacitor will be needed
for stable operation. C
IN
should be located as close
to the device V
IN
pin as practically possible. C
IN
val-
ues greater than 1μF will offer superior input line
transient response and will assist in maximizing the
power supply ripple rejection.
Ceramic, tantalum or aluminum electrolytic capaci-
tors may be selected for C
IN
as there is no specific
capacitor ESR requirement. For 150mA LDO reg-
ulator output operation, ceramic capacitors are rec-
ommended for C
IN
due to their inherent capability
over tantalum capacitors to withstand input current
surges from low impedance sources such as bat-
teries in portable devices.
Output Capacitor
For proper load voltage regulation and operational
stability, a capacitor is required between pins V
OUT
and GND. The C
OUT
capacitor connection to the
LDO regulator ground pin should be made as direct
as practically possible for maximum device per-
formance. The AAT3221/2 has been specifically
designed to function with very low ESR ceramic
capacitors. Although the device is intended to oper-
ate with these low ESR capacitors, it is stable over
a very wide range of capacitor ESR, thus it will also
work with some higher ESR tantalum or aluminum
electrolytic capacitors. However, for best perform-
ance, ceramic capacitors are recommended.
The value of C
OUT
typically ranges from 0.47μF to
10μF, however 1μF is sufficient for most operating
conditions.
If large output current steps are required by an
application, then an increased value for C
OUT
should be considered. The amount of capacitance
needed can be calculated from the step size of the
change in output load current expected and the
voltage excursion that the load can tolerate.
The total output capacitance required can be cal-
culated using the following formula:
C
OUT
=
I × 15μF
V
Where:
I = maximum step in output current
V = maximum excursion in voltage that the load
can tolerate
Note that use of this equation results in capacitor
values approximately two to four times the typical
value needed for an AAT3221/2 at room tempera-
ture. The increased capacitor value is recommend-
ed if tight output tolerances must be maintained over
extreme operating conditions and maximum opera-
tional temperature excursions. If tantalum or alu-
minum electrolytic capacitors are used, the capacitor
value should be increased to compensate for the
substantial ESR inherent to these capacitor types.
Capacitor Characteristics
Ceramic composition capacitors are highly recom-
mended over all other types of capacitors for use
with the AAT3221/2. Ceramic capacitors offer
many advantages over their tantalum and alu-
minum electrolytic counterparts. A ceramic capac-
itor typically has very low ESR, is lower cost, has a
smaller PCB footprint and is non-polarized. Line
and load transient response of the LDO regulator is
improved by using low ESR ceramic capacitors.
Since ceramic capacitors are non-polarized, they
are less prone to damage if connected incorrectly.
Equivalent Series Resistance (ESR):
ESR is a
very important characteristic to consider when
selecting a capacitor. ESR is the internal series
resistance associated with a capacitor, which
includes lead resistance, internal connections,
capacitor size and area, material composition and
ambient temperature. Typically capacitor ESR is
measured in milliohms for ceramic capacitors and
can range to more than several ohms for tantalum
or aluminum electrolytic capacitors.
Ceramic Capacitor Materials:
Ceramic capacitors
less than 0.1μF are typically made from NPO or
COG materials. NPO and COG materials are typi-
cally tight tolerance and very stable over tempera-
ture. Larger capacitor values are typically composed
of X7R, X5R, Z5U and Y5V dielectric materials.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT3221IGV-24-T1 | 150mA NanoPower⑩ LDO Linear Regulator |
| AAT3221IGV-25-T1 | 150mA NanoPower⑩ LDO Linear Regulator |
| AAT3221IGV-28-T1 | 150mA NanoPower⑩ LDO Linear Regulator |
| AAT3222IGV-20-T1 | 150mA NanoPower⑩ LDO Linear Regulator |
| AAT3221 | 150mA NanoPower⑩ LDO Linear Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT3221IGV-35-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:150mA NanoPower⑩ LDO Linear Regulator |
| AAT3221IJS-1.5-T1 | 制造商:Advanced Analogic Tech 功能描述:AAT3221 Series 1.5 V 150 mA NanoPower LDO Linear Regulator - SC-70JW-8 制造商:SKYWORKS SOLUTIONS 功能描述:AAT3221 Series 1.5 V 150 mA NanoPower LDO Linear Regulator - SC-70JW-8 制造商:Skyworks Solutions Inc 功能描述:VOLTAGE REGULATOR |
| AAT3221IJS-1.6-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:150mA NanoPower? LDO Linear Regulator |
| AAT3221IJS-1.7-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:150mA NanoPower⑩ LDO Linear Regulator |
| AAT3221IJS-1.8-T1 | 功能描述:低壓差穩壓器 - LDO 150mA NanoPower LDO Linear Regulator RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:3.1 V 回動電壓（最大值）:160 mV 輸出電流:300 mA 負載調節: 輸出端數量:1 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DFN-4 |
發布緊急采購，3分鐘左右您將得到回復。