- 您現在的位置：買賣IC網 > PDF目錄223291 > A6ER-5101 PIANO DIP SWITCH-1SWITCHES, 5PST, MOMENTARY,0.025A, 24VDC, THROUGH HOLE-RIGHT ANGLE PDF資料下載
參數資料
| 型號： | A6ER-5101 |
| 元件分類： | 開關 |
| 英文描述： | PIANO DIP SWITCH-1SWITCHES, 5PST, MOMENTARY,0.025A, 24VDC, THROUGH HOLE-RIGHT ANGLE |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 729K |
| 代理商： | A6ER-5101 |
6
Precautions
Washing
1. Washable and Non-washable Models
The models for which washing are possible are shown in the fol-
lowing table.
2. Washing Procedure
Ultrasonic cleaning is not available for slide-type DIP Switches
with seal tape. These models may be wiped or dipped into wash-
ing agents for one minute maximum.
Slide-type DIP Switches with seal tape can be washed as long as
the seal tape is not removed or pasted before washing. Non-com-
pliance here will cause the quality of the seal to decline.
Washing equipment incorporating more than one washing bath
can be used to clean washable models, provided that the wash-
able models are cleaned for one minute maximum per bath and
the total cleaning time does not exceed three minutes.
3. Washing Agents
Apply alcohol-based solvents to clean washable models. Do not
apply water or any other agents to clean any washable models,
as such agents may degrade the materials or performance of the
Switch.
4. Washing Precautions
Do not impose any external force on washable models while
washing.
Do not clean washable models immediately after soldering. The
cleaning agent may be absorbed into the incomplete seal through
respiration as the Switch cools. Wait for at least three minutes
after soldering before cleaning.
Do not use washable Switches submerged in water or in locations
exposed to water.
Handling
1. Slide-type DIP Switch operation
Do not apply excessive operating force to the Switch. Otherwise
the Switch may be damaged or deformed, and the switch mecha-
nism may malfunction as a result. Apply an operating force not
exceeding 9.8 N. (Operate each pole separately.) Apply the oper-
ating load from the side of the striker. Do not apply a load from an
angle or from above the striker. Doing so may deform the Switch
contact.
Set slide-type DIP Switches with a tiny, rounded object, such as
the tip of a ball-point pen or a small screwdriver. Do not set the
DIP Switch using tweezers or any other sharp object that may
damage it. Do not set the DIP Switch using the point of a mechan-
ical pencil, or lead powder or fragments may fall into the Switch
and internal circuit board, causing the DIP Switch to malfunction
and reducing the dielectric strength of the circuit board.
Although raised-type and piano-type strikers can be operated by
fingertip, do not push too hard or too fast because this will deform
or damage the striker.
When setting or operating the A6H, use narrow-headed tweezers
or similar implement (without a sharp end), to enable smooth,
horizontal operation. Pushing the striker at an angle, or applying
excessive load from above may damage or deform the striker and
thereby prevent operation.
2. Rotary DIP Switch Operation
Set rotary-type DIP Switches with a flat-blade screwdriver that fits
into the screwdriver groove. Using a screwdriver of inappropriate
dimensions, or using a tool other than a flat-blade screwdriver
may cause damage to the groove that may make the Switch
impossible to operate.
Insert the flat-blade screwdriver vertically to operate the Switch.
The Switch may be damaged if the screwdriver is inserted at an
angle.
Do not use excessive force to operate the Switch, or it may dam-
age or deform the Switch.
3. Setting
Set the Switch to the correct position before use. An incorrectly
aligned position may result in incorrect signals.
Rotary DIP Switch Operation
Washable
A6A, A6C, A6CV, A6D, A6DR, A6T (with seal tape),
A6S-H (with seal tape), A6H (with seal tape)
Non-washable
A6R, A6RV, A6T (standard/raised actuator), A6S-
H (standard/raised actuator), A6E, A6ER
Incorrect
Correct
Item
A6R/A6RV
A6A
A6C/A6CV
Top/Side operation, flat type
Standard type, flat type
Shaft type, wheel type
Top/Side operation type
Screwdriver
groove
Applicable
screwdriver: A
1.8 to 2.1
3.5 to 3.8
2.0 to 2.4
Applicable
screwdriver: B
0.7 to 0.8
0.4 to 0.5
0.5 to 0.6
Part names
1.0
2.9
Depth: 1.0
Depth: 0.9
0.65
4
Depth: 0.9
0.7
4 dia.
Depth: 1.0
2.5
0.8
Flat-blade screwdriver
Groove
A6A, A6C/A6CV, A6R/A6RV
Rotary DIP Switch
A
B
相關PDF資料 |
PDF描述 |
|---|---|
| A6RS-161RS | ROTARY CODED SWITCH-16POSITIONS, REAL CODE, LATCHED, 0.025A, 24VDC, SURFACE MOUNT-STRAIGHT |
| A6RS-162RF | ROTARY CODED SWITCH-16POSITIONS, REAL CODE, LATCHED, 0.025A, 24VDC, SURFACE MOUNT-STRAIGHT |
| A6RV-101RF | ROTARY CODED SWITCH-10POSITIONS, REAL CODE, LATCHED, 0.025A, 24VDC, THROUGH HOLE-RIGHT ANGLE |
| A6SR-6104-P | PIANO DIP SWITCH-6SWITCHES, SPST, MOMENTARY,0.025A, 24VDC, SURFACE MOUNT-STRAIGHT |
| A6TN-7101 | SLIDE DIP SWITCH-7SWITCHES, 7PST, LATCHED,0.025A, 24VDC, THROUGH HOLE-STRAIGHT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A6ER5104 | 制造商:Omron Electronic Components LLC 功能描述:SWIT DIP 5P 5 PIANO 0.025A 24VDC PC PINS 1000CYCLE 2.54MM TH - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH SIDE ACTUATOR LONG 5 WAY 制造商:Omron Electronic Components LLC 功能描述:SWITCH, SIDE ACTUATOR, LONG, 5 WAY 制造商:Omron Electronic Components LLC 功能描述:Switch DIP ON OFF SPST 5 Piano 0.025A 24VDC PC Pins 1000Cycle 2.54mm Thru-Hole Tube |
| A6ER-5104 | 功能描述:DIP 開關/ SIP 開關 DIP SWITCH RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
| A6ER6101 | 制造商:Omron Electronic Components LLC 功能描述:SWIT DIP ON OFF 6P 6 PIANO 0.025A 24VDC PC PINS 1000CYCLE 2. - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH DIP 6POS SIDE ACT SHRT 制造商:Omron Electronic Components LLC 功能描述:Switch DIP 6 way piano act Thru-Hole 制造商:Omron Electronic Components LLC 功能描述:Switch DIP ON OFF SPST 6 Piano 0.025A 24VDC PC Pins 1000Cycle 2.54mm Thru-Hole Tube |
| A6ER-6101 | 功能描述:DIP 開關/ SIP 開關 DIP SWITCH RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
| A6ER6104 | 制造商:Omron Electronic Components LLC 功能描述:SWIT DIP ON OFF 6P 6 PIANO 0.025A 24VDC PC PINS 1000CYCLE 2. - Bulk 制造商:Omron Electronic Components LLC 功能描述:SWITCH DIP 6POS SIDE ACT LONG 制造商:Omron Electronic Components LLC 功能描述:Dip switch,piano type,long lever,6 way 制造商:Omron Electronic Components LLC 功能描述:Switch DIP ON OFF SPST 6 Piano 0.025A 24VDC PC Pins 1000Cycle 2.54mm Thru-Hole Tube |
發布緊急采購，3分鐘左右您將得到回復。