- 您現在的位置：買賣IC網 > PDF目錄375135 > A3282LUA (Allegro MicroSystems, Inc.) Chopper-Stabilized Hall Effect Latch PDF資料下載
參數資料
| 型號： | A3282LUA |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Chopper-Stabilized Hall Effect Latch |
| 中文描述： | 斬波穩定霍爾效應鎖存 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 476K |
| 代理商： | A3282LUA |
8
A3282-DS
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Chopper-Stabilized Hall Effect Latch
A3282
Figure 2. Chopper Stabilization Circuit (Dynamic Quadrature Offset Cancellation)
Amp
Regulator
Clock/Logic
Hall Element
S
H
L
F
Chopper Stabilization Technique
When using Hall-effect technology, a limiting factor for
switchpoint accuracy is the small signal voltage developed
across the Hall element. This voltage is disproportionally small
relative to the offset that can be produced at the output of the
Hall sensor. This makes it dif
fi
cult to process the signal while
maintaining an accurate, reliable output over the speci
fi
ed oper-
ating temperature and voltage ranges.
Chopper stabilization is a unique approach used to minimize
Hall offset on the chip. The patented Allegro technique, namely
Dynamic Quadrature Offset Cancellation, removes key sources
of the output drift induced by thermal and mechanical stresses.
This offset reduction technique is based on a signal modulation-
demodulation process. The undesired offset signal is separated
from the magnetic-
fi
eld-induced signal in the frequency domain,
through modulation. The subsequent demodulation acts as a
modulation process for the offset, causing the magnetic-
fi
eld-
induced signal to recover its original spectrum at baseband,
while the dc offset becomes a high-frequency signal. The mag-
netic-
fi
eld-induced signal then can pass through a low-pass
fi
lter,
while the modulated dc offset is suppressed. This con
fi
guration
is illustrated in
fi
gure 2.
The chopper stabilization technique uses a 200 kHz high-fre-
quency clock. For demodulation process, a sample and hold
technique is used, where the sampling is performed at twice the
chopper frequency (400 kHz). This high-frequency operation
allows a greater sampling rate, which results in higher accuracy
and faster signal-processing capability. This approach desensi-
tizes the chip to the effects of thermal and mechanical stresses,
and produces devices that have extremely stable quiescent Hall
output voltages and precise recoverability after temperature
cycling. This technique is made possible through the use of a
BiCMOS process, which allows the use of low-offset, low-noise
ampli
fi
ers in combination with high-density logic integration and
sample-and-hold circuits.
The repeatability of magnetic-
fi
eld-induced switching is affected
slightly by a chopper technique. However, the Allegro high-
frequency chopping approach minimizes the affect of jitter and
makes it imperceptible in most applications. Applications that
are more likely to be sensitive to such degradation are those
requiring precise sensing of alternating magnetic
fi
elds; for
example, speed sensing of ring-magnet targets. For such applica-
tions, Allegro recommends its digital sensor families with lower
sensitivity to jitter. For more information on those devices,
contact your Allegro sales representative.
相關PDF資料 |
PDF描述 |
|---|---|
| A3282LUA-T | Chopper-Stabilized Hall Effect Latch |
| A33-1 | 2 TO 2400 MHz CASCADABLE AMPLIFIER |
| A3361 | 2-Wire,Chopper-Stabilized, Hall Effect Switch(2線,斬波穩定，霍爾效應開關) |
| A3362 | 2-Wire,Chopper-Stabilized, Hall Effect Switch(2線,斬波穩定，霍爾效應開關) |
| A3421 | Hall Effect Direction-Detection Sensor(霍爾效應定位檢測傳感器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A3282LUA-T | 功能描述:IC SW HALL EFFECT CHOPPER 3-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A3283ELH | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION |
| A3283ELH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CHOPPER-STABILIZED， PRECISION HALL-EFFECT LATCHES |
| A3283ELHLT | 功能描述:IC SWITCH HALL EFFECT SOT23W RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。