- 您現在的位置：買賣IC網 > PDF目錄375131 > A3064 (Allegro MicroSystems, Inc.) HALL-EFFECT GEAR-TOOTH SENSOR -AC COUPLED PDF資料下載
參數資料
| 型號： | A3064 |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | HALL-EFFECT GEAR-TOOTH SENSOR -AC COUPLED |
| 中文描述： | 霍爾效應齒輪齒傳感器交流耦合 |
| 文件頁數： | 1/8頁 |
| 文件大?。?/td> | 143K |
| 代理商： | A3064 |
The A3064LKA ac-coupled Hall-effect gear-tooth sensor is a
monolithic integrated circuit that switches in response to changing
differential magnetic fields created by moving ferrous targets. This
device is ideal for use in non-zero-speed, gear-tooth-based speed,
position, and timing applications such as in anti-lock braking systems,
transmissions, and crankshafts.
When coupled with a back-biasing magnet, the sensor can be
configured to turn on or off with the leading or trailing edge of a gear-
tooth or slot. Changes in fields on the magnet face caused by a moving
ferrous mass are sensed by two integrated Hall transducers and are
differentially amplified by on-chip electronics. This differential
sensing design provides immunity to radial vibration within the
device’s operating air gap. Steady-state magnet and system offsets are
eliminated using an on-chip differential band-pass filter. This filter
also provides relative immunity to interference from RF and electro-
magnetic sources. The on-chip temperature compensation and Schmitt
trigger circuitry minimizes shifts in effective working air gaps and
switch points over temperature, allowing operation to low frequencies
over a wide range of air gaps and temperatures.
Each Hall-effect digital Integrated circuit includes a voltage
regulator, two quadratic Hall-effect sensing elements, temperature
compensating circuitry, a low-level amplifier, band-pass filter, Schmitt
trigger, and an open-collector output driver. The on-board regulator
permits operation with supply voltages of 4.5 to 24 volts. The output
stage can easily switch 20 mA over the full frequency response range
of the sensor and is compatible with bipolar and MOS logic circuits.
The device is packaged in a 5-pin plastic SIP.
FEATURES
I
Senses Motion of Ferrous Targets
I
Wide Operating Temperature Range
I
Operation to 30 kHz
I
Resistant to EMI
I
Large Effective Air Gap
I
4.5 V to 24 V Operation
I
Output Compatible With All Logic Families
I
Reverse Battery Protection
I
Resistant to Physical Stress
HALL-EFFECT GEAR-TOOTH SENSOR
—AC COUPLED
Always order by complete part number, e.g.,
A3064LKA
.
D
2
ABSOLUTE MAXIMUM RATINGS
at T
A
= +25
°
C
Supply Voltage, V
CC
.............................
24 V
Reverse Battery Voltage, V
RCC
..........
-30 V
Magnetic Flux Density, B............
Unlimited
Output Off Voltage, V
OUT
......................
24 V
Output Current, I
OUT
.........................
25 mA
Package Power Dissipation,
P
D
............................................
500 mW
Operating Temperature Range,
T
A
...............................
-40
°
C to +150
°
C
Storage Temperature Range,
T
S
...............................
-65
°
C to +170
°
C
VCC
1
4
3
2
5
X
X
Dwg. PH-011-1
S
O
G
F
F
Pinning is shown viewed from branded side.
3064
相關PDF資料 |
PDF描述 |
|---|---|
| A3064LKA | HALL-EFFECT GEAR-TOOTH SENSOR -AC COUPLED |
| A3064LKA-TL | HALL-EFFECT GEAR-TOOTH SENSOR -AC COUPLED |
| A30RBE | Center Tap Chip Resistor |
| A30RDC | Center Tap Chip Resistor |
| A30RDE | Center Tap Chip Resistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A3064L | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:HALL-EFFECT GEAR-TOOTH SENSORS -ACCOUPLED |
| A3064LKA | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:HALL-EFFECT GEAR-TOOTH SENSOR -AC COUPLED |
| A3064LKA-TL | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:HALL-EFFECT GEAR-TOOTH SENSOR -AC COUPLED |
| A30664250AP | 制造商:Panasonic Industrial Company 功能描述:UPPER SASH |
| A3068MBAA1 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:SCA CONNECTOR IDC TYPE(MALE) |
發布緊急采購，3分鐘左右您將得到回復。