- 您現在的位置：買賣IC網 > PDF目錄375122 > A29L800AUV-70UF (AMIC Technology Corporation) 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | A29L800AUV-70UF |
| 廠商： | AMIC Technology Corporation |
| 英文描述： | 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| 中文描述： | 100萬× 8位/ 16位為512k ×電壓的CMOS 3.0只，引導扇區閃存 |
| 文件頁數： | 13/36頁 |
| 文件大?。?/td> | 503K |
| 代理商： | A29L800AUV-70UF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
A29L800A Series
(June, 2005, Version 1.1)
12
AMIC Technology, Corp.
START
Write Erase
Command
Sequence
Data Poll
from System
Data = FFh
Erasure Completed
Yes
Embedded
Erase
algorithm in
progress
Note :
1. See the appropriate Command Definitions table for erase
command sequences.
2. See "I/O
3
: Sector Erase Timer" for more information.
No
Figure 2. Erase Operation
section.) The time-out begins from the rising edge of the final
WE
pulse in the command sequence.
Once the sector erase operation has begun, only the Erase
Suspend command is valid. All other commands are ignored.
When the Embedded Erase algorithm is complete, the device
returns to reading array data and addresses are no longer
latched. The system can determine the status of the erase
operation by using I/O
7
, I/O
6
, or I/O
2
. Refer to "Write Operation
Status" for information on these status bits.
Figure 2 illustrates the algorithm for the erase operation. Refer
to the Erase/Program Operations tables in the "AC
Characteristics" section for parameters, and to the Sector
Erase Operations Timing diagram for timing waveforms.
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to interrupt a
sector erase operation and then read data from, or program
data to, any sector not selected for erasure. This command is
valid only during the sector erase operation, including the 50
μ
s
time-out period during the sector erase command sequence.
The Erase Suspend command is ignored if written during the
chip erase operation or Embedded Program algorithm. Writing
the Erase Suspend command during the Sector Erase time-out
immediately terminates the time-out period and suspends the
erase operation. Addresses are "don't cares" when writing the
Erase Suspend command.
When the Erase Suspend command is written during a sector
erase operation, the device requires a maximum of 20
μ
s to
suspend the erase operation. However, when the Erase
Suspend command is written during the sector erase time-out,
the device immediately terminates the time-out period and
suspends the erase operation.
After the erase operation has been suspended, the system can
read array data from or program data to any sector not
selected for erasure. (The device "erase suspends" all sectors
selected for erasure.) Normal read and write timings and
command definitions apply. Reading at any address within
erase-suspended sectors produces status data on I/O
7
- I/O
0
.
The system can use I/O
7
, or I/O
6
and I/O
2
together, to
determine if a sector is actively erasing or is erase-suspended.
See "Write Operation Status" for information on these status
bits.
After an erase-suspended program operation is complete, the
system can once again read array data within non-suspended
sectors. The system can determine the status of the program
operation using the I/O
7
or I/O
6
status bits, just as in the
standard program operation. See "Write Operation Status" for
more information.
The system may also write the autoselect command sequence
when the device is in the Erase Suspend mode. The device
allows reading autoselect codes even at addresses within
erasing sectors, since the codes are not stored in the memory
array. When the device exits the autoselect mode, the device
reverts to the Erase Suspend mode, and is ready for another
valid operation. See "Autoselect Command Sequence" for
more information.
The system must write the Erase Resume command (address
bits are "don't care") to exit the erase suspend mode and
continue the sector erase operation. Further writes of the
Resume command are ignored. Another Erase Suspend
command can be written after the device has resumed erasing.
相關PDF資料 |
PDF描述 |
|---|---|
| A29L800AUV-90 | MS3106A16-10PW |
| A29L800AUV-90F | 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800ATV-90UF | 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800ATG-90UF | 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800AUV-90UF | 1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A29L800AUV-90 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800AUV-90F | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800AUV-90U | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800AUV-90UF | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| A29L800AV | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1M X 8 Bit / 512K X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。