參數資料
型號: A29L160AUM-90U
廠商: AMIC Technology Corporation
英文描述: Replaced by PT78NR152,PT78ST153 : 5.25Vout 1.5A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 85
中文描述: 2米x 8位/ 1米× 16位CMOS 3.3伏只,引導扇區閃存
文件頁數: 21/42頁
文件大?。?/td> 572K
代理商: A29L160AUM-90U
A29L160A Series
(May, 2005, Version 0.1)
20
AMIC Technology, Corp.
The I/O
5
failure condition may appear if the system tries to
program a "1 "to a location that is previously programmed to
"0." Only an erase operation can change a "0" back to a "1."
Under this condition, the device halts the operation, and
when the operation has exceeded the timing limits, I/O
5
produces a "1."
Under both these conditions, the system must issue the reset
command to return the device to reading array data.
I/O
3
: Sector Erase Timer
After writing a sector erase command sequence, the system
may read I/O
3
to determine whether or not an erase
operation has begun. (The sector erase timer does not apply
to the chip erase command.) If additional sectors are
selected for erasure, the entire time-out also applies after
each additional sector erase command. When the time-out is
complete, I/O
3
switches from "0" to "1." The system may
ignore I/O
3
if the system can guarantee that the time
between additional sector erase commands will always be
less than 50
μ
s. See also the "Sector Erase Command
Sequence" section.
After the sector erase command sequence is written, the
system should read the status on I/O
7
(
Data
Polling) or I/O
6
(Toggle Bit 1) to ensure the device has accepted the
command sequence, and then read I/O
3
. If I/O
3
is "1", the
internally controlled erase cycle has begun; all further
commands (other than Erase Suspend) are ignored until the
erase operation is complete. If I/O
3
is "0", the device will
accept additional sector erase commands. To ensure the
command has been accepted, the system software should
check the status of I/O
3
prior to and following each
subsequent sector erase command. If I/O
3
is high on the
second status check, the last command might not have been
accepted. Table 10 shows the outputs for I/O
3
.
START
Read I/O
7
-I/O
0
Toggle Bit
= Toggle
Program/Erase
Operation Not
Commplete, Write
Reset Command
Yes
Notes :
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as I/O
5
changes to "1". See text.
No
Read I/O
7
- I/O
0
Twice
I/O
5
= 1
Toggle Bit
= Toggle
Yes
Yes
Program/Erase
Operation Complete
No
No
Read I/O
7
-I/O
0
(Notes 1,2)
Figure 6. Toggle Bit Algorithm
(Note 1)
相關PDF資料
PDF描述
A29L160AUV-90U Replaced by PT78NR152,PT78ST153 : 5.25Vout 1.5A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 85
A29L160AV Replaced by PT78NR152,PT78ST153 : 5.25Vout 1.5A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 85
A29L160TM-90 Replaced by PT78NR152,PT78ST153 : 5.25Vout 1.5A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 85
A29L160UM-90 2M X 8 Bit / 1M X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L160ATM-70I 2M X 8 Bit / 1M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory
相關代理商/技術參數
參數描述
A29L160AUM-90UF 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory
A29L160AUV-70 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory
A29L160AUV-70F 制造商:AMIC Technology 功能描述:IC SM FLASH 16MB 3V BOTTOM BOOT 制造商:AMIC Technology 功能描述:IC, SM, FLASH, 16MB, 3V, BOTTOM BOOT 制造商:AMIC Technology 功能描述:IC, SM, FLASH, 16MB, 3V, BOTTOM BOOT, Memory Type:Boot Sector Flash, Memory Size:16Mbit, Memory Configuration:2M x 8, 1M x 16, Supply Voltage Min:2.7V, Supply Voltage Max:3.6V, Memory Case Style:TSOP, No. of Pins:48, Access , RoHS Compliant: Yes
A29L160AUV-70I 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory
A29L160AUV-70IF 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:2M X 8 Bit / 1M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory