參數資料
型號： A29L040AX-70
廠商： AMIC Technology Corporation
英文描述： Insulation Tester (Megohmmeter); Resistance Measuring Range:0 to 9999 Ohm; Accuracy:+/-3% Rdg +/- 5 LSD Less Than 1Gohm; Display Technology:LED; Range:0 - 4.000/40.00/400.0/4000 Mohm; Test Voltage:1000V; Voltage Rating:1000V RoHS Compliant: NA
中文描述： 為512k × 8位CMOS 3.0伏只，統一部門快閃記憶體
文件頁數： 7/32頁
文件大?。?/td> 303K
代理商： A29L040AX-70
A29L040 Series
PRELIMINARY (June, 2003, Version 0.1)
6
AMIC Technology, Corp.
Autoselect Mode
The autoselect mode provides manufacturer and device
identification, and sector protection verification, through
identifier codes output on I/O
7
- I/O
0
. This mode is primarily
intended for programming equipment to automatically
match a device to be programmed with its corresponding
programming algorithm. However, the autoselect codes
can also be accessed in-system through the command
register.
When using programming equipment, the autoselect mode
requires V
ID
(11.5V to 12.5 V) on address pinA9. Address
pins A6, A1, and AO must be as shown in Autoselect
Codes (High Voltage Method) table. In addition, when
Table 3. A29L040 Autoselect Codes (High Voltage Method)
verifying sector protection, the sector address must appear
on the appropriate highest order address bits. Refer to the
corresponding Sector Address Tables. The Command
Definitions table shows the remaining address bits that are
don't care. When all necessary bits have been set as
required, the programming equipment may then read the
corresponding identifier code on I/O
7
- I/O
0
.To access the
autoselect codes in-system, the host system can issue the
autoselect command via the command register, as shown
in the Command Definitions table. This method does not
require V
ID
. See "Command Definitions" for details on
using the autoselect mode.
Description
A18 - A16 A15 - A10 A9 A8 - A7 A6 A5 - A2
A1
AO
Identifier Code on
I/O
7
- I/O
0
Manufacturer ID: AMIC
X
X
V
ID
X
V
IL
X
V
IL
V
IL
37h
Device ID: A29L040
X
X
V
ID
X
V
IL
X
V
IL
V
IH
92h
01h (protected)
Sector Protection
Verification
Sector
Address
X
V
ID
X
V
IL
X
V
IH
V
IL
00h (unprotected)
Continuation ID
X
X
V
ID
X
V
IL
X
V
IH
V
IH
7Fh
Sector Protection/Unprotection
The hardware sector protection feature disables both
program and erase operations in any sector. The hardware
sector unprotection feature re-enables both program and
erase operations in previously protected sectors.
Sector protection/unprotection must be implemented using
programming equipment. The procedure requires a high
voltage (V
ID
) on address pin A9 and the control pins.
The device is shipped with all sectors unprotected.
It is possible to determine whether a sector is protected or
unprotected. See "Autoselect Mode" for details.
Hardware Data Protection
The requirement of command unlocking sequence for
programming or erasing provides data protection against
inadvertent writes (refer to the Command Definitions table).
In addition, the following hardware data protection measures
prevent accidental erasure or programming, which might
otherwise be caused by spurious system level signals during
V
CC
power-up transitions, or from system noise. The device
is powered up to read array data to avoid accidentally writing
data to the array.
Write Pulse "Glitch" Protection
Noise pulses of less than 5ns (typical) on
OE
,
CE
or
WE
do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of
OE
=V
IL
,
CE
= V
IH
or
WE
= V
IH
. To initiate a write cycle,
CE
and
WE
must be a logical zero while
OE
is a logical one.
Power-Up Write Inhibit
If
WE
=
CE
= V
IL
and
OE
= V
IH
during power up, the
device does not accept commands on the rising edge of
WE
. The internal state machine is automatically reset to
reading array data on the initial power-up.
相關PDF資料
PDF描述
A29L040AX-70F Insulation Tester (Megohmmeter); Resistance Measuring Range:0 to 4000 MOhm; Test Voltage:600V; Voltage Rating:600V RoHS Compliant: NA
A29L160AUG-70 2M X 8 Bit / 1M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory
A29L160AUG-70F 2M X 8 Bit / 1M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory
A29L160AUG-70I Circular Connector; No. of Contacts:16; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:36; Circular Contact Gender:Socket; Circular Shell Style:Box Mount Receptacle RoHS Compliant: No
A29L160AUG-70IF 2M X 8 Bit / 1M X 16 Bit CMOS 3.3 Volt-only, Boot Sector Flash Memory
相關代理商/技術參數
參數描述
A29L040AX-70F 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory
A29L040AY 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory
A29L040AY-70 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory
A29L040AY-70F 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory
A29L040L-55F 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*