參數資料
型號： A29L004V
廠商： AMIC Technology Corporation
英文描述： Replaced by PT78ST106,PT78NR106 : 6Vout 1.5A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 85
中文描述： 為512k × 8位CMOS 3.0伏只，引導扇區閃存
文件頁數： 15/39頁
文件大?。?/td> 370K
代理商： A29L004V
A29L004 Series
PRELIMINARY (October, 2002, Version 0.0)
15
AMIC Technology, Corp.
Table 5. A29L004 Command Definitions
Bus Cycles (Notes 2 - 5)
First
Second
Third
Fourth
Fifth
Sixth
Command Sequence
(Note 1)
C
Addr Data Addr Data
Addr Data Addr Data Addr Data Addr Data
Read (Note 6)
1
RA
RD
Reset (Note 7)
Manufacturer ID
1
4
XXX
555
F0
AA
2AA 55
555
90
X00
37
Device ID,
Top Boot Block
Device ID,
Bottom Boot Block
Continuation ID
4
555
AA
2AA 55
555
90
X01
34
4
555
AA
2AA
55
555
90
X01
B5
4
555
AA
2AA
55
555
90
X03
7F
XX00
A
Sector Protect Verify
(Note 9)
4
555
AA
2AA
55
555
90
(SA)
X02 XX01
Program
4
555
AA
2AA
55
555
A0
PA
PD
Unlock Bypass
3
555
AA
2AA
55
555
20
Unlock Bypass Program (Note 10)
2
XXX A0
PA
PD
Unlock Bypass Reset (Note 11)
Chip Erase
2
6
XXX 90
555
XXX
2AA
00
55
AA
555
80
555
AA
2AA
55
555
10
Sector Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Erase Suspend (Note 12)
1
XXX
B0
Erase Resume (Note 13)
1
XXX
30
Legend:
X = Don't care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the
WE
or
CE
pulse,
whichever happens later.
PD = Data to be programmed at location PA. Data latches on the rising edge of
WE
or
CE
pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A18 - A13 select a unique sector.
Note:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
3. Except when reading array or autoselect data, all bus cycles are write operation.
4. Address bits A18 - A11 are don't cares for unlock and command cycles, unless SA or PA required.
5. No unlock or command cycles required when reading array data.
6. The Reset command is required to return to reading array data when device is in the autoselect mode, or if I/O
5
goes high
(while the device is providing status data).
7. The fourth cycle of the autoselect command sequence is a read cycle.
8. The data is 00h for an unprotected sector and 01h for a protected sector. See “Autoselect Command Sequence” for more
information.
9. The Unlock Bypass command is required prior to the Unlock Bypass Program command.
10. The Unlock Bypass Reset command is required to return to reading array data when the device is in the unlock bypass
mode.
11. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode.
12. The Erase Resume command is valid only during the Erase Suspend mode.
相關PDF資料
PDF描述
A29L004W 512K X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L004X 512K X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L004 512K X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L004TL-70 512K X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L004TL-90 512K X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
相關代理商/技術參數
參數描述
A29L004W 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L004X 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L008 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1M X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L008A 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1M X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
A29L008ATV-70 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1M X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*