- 您現在的位置：買賣IC網 > PDF目錄375112 > A29800UM-70 (AMIC Technology Corporation) 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | A29800UM-70 |
| 廠商： | AMIC Technology Corporation |
| 英文描述： | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| 中文描述： | 1024K × 8位/ 16位為512k ×電壓的CMOS 5.0只，引導扇區閃存 |
| 文件頁數： | 12/34頁 |
| 文件大?。?/td> | 514K |
| 代理商： | A29800UM-70 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
A29800 Series
PRELIMINARY (May, 2001, Version 0.0)
12
AMIC Technology, Inc.
START
Write Erase
Command
Sequence
Data Poll
from System
Data = FFh
Erasure Completed
Yes
Embedded
Erase
algorithm in
progress
Note :
1. See the appropriate Command Definitions table for erase
command sequences.
2. See "I/O
3
: Sector Erase Timer" for more information.
No
Figure 3. Erase Operation
Figure 3 illustrates the algorithm for the erase operation.
Refer to the Erase/Program Operations tables in the "AC
Characteristics" section for parameters, and to the Sector
Erase Operations Timing diagram for timing waveforms.
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to interrupt
a sector erase operation and then read data from, or
program data to, any sector not selected for erasure. This
command is valid only during the sector erase operation,
including the 50
μ
s time-out period during the sector erase
command sequence. The Erase Suspend command is
ignored if written during the chip erase operation or
Embedded Program algorithm. Writing the Erase Suspend
command during the Sector Erase time-out immediately
terminates the time-out period and suspends the erase
operation. Addresses are "don't cares" when writing the
Erase Suspend command.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum of
20
μ
s to suspend the erase operation. However, when the
Erase Suspend command is written during the sector erase
time-out, the device immediately terminates the time-out
period and suspends the erase operation.
After the erase operation has been suspended, the system
can read array data from or program data to any sector not
selected for erasure. (The device "erase suspends" all
sectors selected for erasure.) Normal read and write timings
and command definitions apply. Reading at any address
within erase-suspended sectors produces status data on I/O
7
- I/O
0
. The system can use I/O
7
, or I/O
6
and I/O
2
together, to
determine if a sector is actively erasing or is erase-
suspended. See "Write Operation Status" for information on
these status bits.
After an erase-suspended program operation is complete,
the system can once again read array data within non-
suspended sectors. The system can determine the status of
the program operation using the I/O
7
or I/O
6
status bits, just
as in the standard program operation. See "Write Operation
Status" for more information.
The system may also write the autoselect command
sequence when the device is in the Erase Suspend mode.
The device allows reading autoselect codes even at
addresses within erasing sectors, since the codes are not
stored in the memory array. When the device exits the
autoselect mode, the device reverts to the Erase Suspend
mode, and is ready for another valid operation. See
"Autoselect Command Sequence" for more information.
The system must write the Erase Resume command
(address bits are "don't care") to exit the erase suspend
mode and continue the sector erase operation. Further
writes of the Resume command are ignored. Another Erase
Suspend command can be written after the device has
resumed erasing.
相關PDF資料 |
PDF描述 |
|---|---|
| A29800 | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TM-90 | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800UM-90 | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TM-70 | 128 x 64 pixel format, LED Backlight available |
| A29800TV-55 | 240 x 128 pixel format, CFL Backlight with power harness |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A29800UM-70F | 制造商:AMIC Technology 功能描述:FLASH 5V BOTTOM SECTOR 8MB 29800 |
| A29800UM-90 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800UV-55 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800UV-70 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800UV-70F | 制造商:AMIC Technology 功能描述:FLASH 5V BOTTOM SECTOR 8MB 29800 |
發布緊急采購，3分鐘左右您將得到回復。