- 您現(xiàn)在的位置：買賣IC網 > PDF目錄375112 > A29800TM-55 (AMIC Technology Corporation) 128 x 64 pixel format, LED Backlight available PDF資料下載
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁
A29800 Series
PRELIMINARY (May, 2001, Version 0.0)
29
AMIC Technology, Inc.
Timing Waveforms for Alternate
CE
Controlled Write Operation (
RESET
=V
IH
on A29800)
Addresses
WE
OE
CE
Data
555 for program
2AA for erase
PA
D
OUT
~
~
I/O
7
~
~
~
Data Polling
Note :
1. PA = Program Address, PD = Program Data, SA = Sector Address, I/O
7
= Complement of Data Input, D
OUT
= Array Data.
2. Figure indicates the last two bus cycles of the command sequence.
PD for program
30 for sector erase
10 for chip erase
~
t
BUSY
t
WHWH1 or 2
t
AH
t
AS
t
WC
t
WH
t
GHEL
t
CP
t
WS
t
CPH
PA for program
SA for sector erase
555 for chip erase
A0 for program
55 for erase
t
RH
t
DS
t
DH
~
~
RESET
RY/BY
Erase and Programming Performance
Parameter
Typ. (Note 1)
1.0
11
35
60
7.2
Max. (Note 2)
8
300
500
21.6
Unit
sec
sec
μ
s
μ
s
sec
Comments
Sector Erase Time
Chip Erase Time (Note 3)
Byte Programming Time
Word Programming Time
Chip Programming Time
(Note 3)
Excludes 00h programming
prior to erasure (Note 4)
Byte Mode
Word Mode
6.3
18.6
sec
Excludes system-level
overhead (Note 5)
Notes:
1. Typical program and erase times assume the following conditions: 25
°
C, 5.0V VCC, 10,000 cycles. Additionally,
programming typically assumes checkerboard pattern.
2. Under worst case conditions of 90
°
C, VCC = 4.5V (4.75V for -55), 100,000 cycles.
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most
bytes program faster than the maximum byte program time listed. If the maximum byte program time given is exceeded,
only then does the device set I/O
5
= 1. See the section on I/O
5
for further information.
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the four-bus-cycle command sequence for programming. See
Table 4 for further information on command definitions.
6. The device has a guaranteed minimum erase and program cycle endurance of 100,000 cycles.
相關PDF資料 |
PDF描述 |
|---|---|
| A29800UM-55 | PWR SUPPLY PROG ONE 17.5/35V OUT |
| A29800UM-70 | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800 | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TM-90 | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800UM-90 | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
相關代理商/技術參數(shù) |
參數(shù)描述 |
|---|---|
| A29800TM-70 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TM-90 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TV-55 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TV-70 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29800TV-90 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
發(fā)布緊急采購，3分鐘左右您將得到回復。