參數資料
型號： A29010V-90
廠商： AMIC Technology Corporation
英文描述： Hook-Up Wire; Conductor Size AWG:24; No. Strands x Strand Size:19 x 36; Jacket Color:Purple; Approval Bodies:UL; Approval Categories:UL AWM Style 1180; Passes VW-1 Flame Test; Cable/Wire MIL SPEC:MIL-W-16878/5 Type EE RoHS Compliant: Yes
中文描述： 128K的× 8位CMOS 5.0伏只，統一部門快閃記憶體
文件頁數： 8/30頁
文件大小： 288K
代理商： A29010V-90
A29010 Series
PRELIMINARY (August, 2001, Version 0.3)
8
AMIC Technology, Inc.
Autoselect Command Sequence
The autoselect command sequence allows the host system
to access the manufacturer and devices codes, and
determine whether or not a sector is protected. The
Command Definitions table shows the address and data
requirements. This method is an alternative to that shown in
the Autoselect Codes (High Voltage Method) table, which is
intended for PROM programmers and requires V
ID
on
address bit A9.
The autoselect command sequence is initiated by writing two
unlock cycles, followed by the autoselect command. The
device then enters the autoselect mode, and the system may
read at any address any number of times, without initiating
another command sequence.
Byte Program Command Sequence
Programming is a four-bus-cycle operation. The program
command sequence is initiated by writing two unlock write
cycles, followed by the program set-up command. The
program address and data are written next, which in turn
initiate the Embedded Program algorithm. The system is not
required to provide further controls or timings. The device
automatically provides internally generated program pulses
and verify the programmed cell margin. The Command
Definitions table shows the address and data requirements
for the byte program command sequence.
When the Embedded Program algorithm is complete, the
device then returns to reading array data and addresses are
no longer latched. The system can determine the status of
the program operation by using I/O
7
or I/O
6
. See "Write
Operation Status" for information on these status bits.
Any commands written to the device during the Embedded
Program Algorithm are ignored. Programming is allowed in
any sequence and across sector boundaries. A bit cannot be
programmed from a "0" back to a "1 ". Attempting to do so
may halt the operation and set I/O
5
to "1", or cause the
Data
Polling algorithm to indicate the operation was
successful. However, a succeeding read will show that the
data is still "0". Only erase operations can convert a "0" to a
"1".
START
Write Program
Command
Sequence
Data Poll
from System
Verify Data
Last Address
Programming
Completed
No
Yes
Yes
Increment Address
Embedded
Program
algorithm in
progress
Note : See the appropriate Command Definitions table for
program command sequence.
Figure 1. Program Operation
相關PDF資料
PDF描述
A29040A 512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory
A29040AV-55 Fuse; Current Rating:1A; Voltage Rating:600V; Voltage Rating:600V; Voltage, AC:600V RoHS Compliant: NA
A29040V-90 512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory
A29040L-120 512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory
A29040L-150 512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory
相關代理商/技術參數
參數描述
A29022-000 制造商:TE Connectivity 功能描述:VARISTOR 300V 14MM RADIAL T/R 制造商:TE Connectivity 功能描述:VARISTOR 300V 6.5KA DISC 14MM
A29040 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory
A29040-120 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory
A29040-150 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory
A29040-55 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*