- 您現在的位置：買賣IC網 > PDF目錄375110 > A29010-55 (AMIC Technology Corporation) 128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory PDF資料下載
參數資料
| 型號： | A29010-55 |
| 廠商： | AMIC Technology Corporation |
| 英文描述： | 128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| 中文描述： | 128K的× 8位CMOS 5.0伏只，統一部門快閃記憶體 |
| 文件頁數： | 14/30頁 |
| 文件大?。?/td> | 288K |
| 代理商： | A29010-55 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
I/O
3
: Sector Erase Timer
A29010 Series
PRELIMINARY (August, 2001, Version 0.3)
14
AMIC Technology, Inc.
After writing a sector erase command sequence, the
system may read I/O
3
to determine whether or not an
erase operation has begun. (The sector erase timer does
not apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out also
applies after each additional sector erase command.
When the time-out is complete, I/O
3
switches from "0" to
"1." The system may ignore I/O
3
if the system can
guarantee that the time between additional sector erase
commands will always be less than 50
μ
s. See also the
"Sector Erase Command Sequence" section.
After the sector erase command sequence is written, the
system should read the status on I/O
7
(
Data
Polling) or
I/O
6
(Toggle Bit 1) to ensure the device has accepted the
command sequence, and then read I/O
3
. If I/O
3
is "1", the
internally controlled erase cycle has begun; all further
commands (other than Erase Suspend) are ignored until
the erase operation is complete. If I/O
3
is "0", the device
will accept additional sector erase commands. To ensure
the command has been accepted, the system software
should check the status of I/O
3
prior to and following each
subsequent sector erase command. If I/O
3
is high on the
second status check, the last command might not have
been accepted. Table 5 shows the outputs for I/O
3
.
START
Read I/O
7
-I/O
0
Toggle Bit
= Toggle
Program/Erase
Operation Not
Commplete, Write
Reset Command
Yes
Notes :
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as I/O
5
changes to "1". See text.
No
Read I/O
7
- I/O
0
Twice
I/O
5
= 1
Toggle Bit
= Toggle
Yes
Yes
Program/Erase
Operation Complete
No
No
Read I/O
7
-I/O
0
(Notes 1,2)
Figure 4. Toggle Bit Algorithm
(Note 1)
相關PDF資料 |
PDF描述 |
|---|---|
| A29010L-55 | 128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| A29010L-70 | 128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| A29010L-90 | 128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| A29010-70 | 128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| A29010-90 | Circular Connector; No. of Contacts:22; Series:TVS06; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:13; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:13-35 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A29010-70 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| A29010-70F | 制造商:AMIC Technology 功能描述:MEMORY FLASH NOR 5V 1M 32DIP 制造商:AMIC Technology 功能描述:MEMORY, FLASH, NOR, 5V, 1M, 32DIP 制造商:AMIC Technology 功能描述:MEMORY, FLASH, NOR, 5V, 1M, 32DIP; Memory Type:Flash - NOR; Memory Size:1Mbit; Memory Configuration:128K x 8bit; Supply Voltage Min:4.5V; Supply Voltage Max:5.5V; Memory Case Style:DIP; No. of Pins:32; Access Time:70ns; Interface ;RoHS Compliant: Yes |
| A29010-90 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| A29010L-55 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| A29010L-70 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:128K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。