- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1361LKTTN-T (Allegro Microsystems Inc)IC HALL EFFECT SENSOR LN 4-SIP Datasheet資料下載
參數資料
| 型號： | A1361LKTTN-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 24/26頁 |
| 文件大?。?/td> | 618K |
| 描述： | IC HALL EFFECT SENSOR LN 4-SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 1 |
| 傳感范圍： | 1.4mV/G ~ 4.5mV/G |
| 類型： | 線性 - 單極，雙極 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 12mA |
| 電流 - 輸出（最大）： | 10mA |
| 輸出類型： | 模擬，比率 |
| 特點： | 可編程 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 4-SIP |
| 供應商設備封裝： | 4-SIP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1139 (CN2011-ZH PDF) |
| 其它名稱： | 620-1234-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁
A1360, A1361,
and A1362
Improving Sensing System Accuracy Using the FILTER Pin
In low-frequency sensing applications, it is often advantageous
to add a simple RC filter to the output of the sensor IC. Such a
low-pass filter improves the signal-to-noise ratio, and therefore
the resolution, of the device output signal. However, the addition
of an RC filter to the output of a sensor IC can result in undesir-
able device output attenuation even for DC signals.
Signal attenuation, V
ATT
, is a result of the resistive divider
effect between the resistance of the external filter, R
EXT
(see fig-
ure 10), and the input impedance and resistance of the customer
interface circuit, R
INTFC
. The transfer function of this resistive
divider is given by:
Even if R
EXT
and R
INTFC
are designed to match, the two individ-
ual resistance values will most likely drift by different amounts
over temperature. Therefore, signal attenuation will vary as a
function of temperature. Note that the input impedance, R
INTFC
,
of commonly available analog-to-digital converters (ADC) can
be as low as 10 k?
The A136x contains an internal resistor with buffer amplifier that
can be connected via the FILTER pin to the PCB. With this cir-
cuit architecture, users can implement a simple RC filter via the
addition of a capacitor, C
FILTER
(see figure 11) from the FILTER
pin to ground. The buffer amplifier inside of the A136x (located
after the internal resistor and FILTER pin connection) eliminates
the attenuation caused by the resistive divider effect described in
equation 16. Therefore, the A136x device is ideal for use in high-
accuracy applications that require a large signal-to-noise ratio
and cannot afford the signal attenuation associated with the use
of an external RC low-pass filter.
=
V
ATT
R
INTFC
R
EXT
+ R
INTFC
V
OUT
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
.
(16)
Figure 10. When a low pass filter is constructed externally
to a standard Hall effect device, a resistive divider may
exist between the filter resistor, R
EXT,
and the application
load resistance, R
INTFC
. This resistive divider (shaded
area) will cause excessive attenuation, as given by the
transfer function shown in equation 16.
Application
Interface
Circuit
Buffer Amplifier
and Resistor
R
INTFC
Application
Interface
Circuit
Resistive Divider
R
INTFC
C
FILTER
Amp
GND
VOU
Standard Hall Effect Device
Low Pass Filter
R
EXT
C
EXT
T
VCC
Out
Offset
Trim
Control
Gain
V+
Ratiometric
Hall Drive
Sens TC Trim
(Factory
Programmed)
Sensitivity Trim
8 Bits
(Customer
Programmed)
V
OUT(Q)
8 Fine Bits
1 Coarse Bit
(Customer
Programmed)
FILTER
Allegro A136x
VCC
GND
Program/Lock
Programming
Logic
C
BYPASS
0.01 糉
V+
Signal Recovery
VOUT
C
BYPASS
0.01 糉
tv v r
INTF
Figure 11. The FILTER pin provided
on the A136x device allows separate
control of SNR, avoiding the attenua-
tion effects from the standard resistor
divider solution, shown in figure 10.
Low-Noise Programmable Linear Hall Effect Sensor ICs with
Adjustable Bandwidth (50 kHz Maximum) and Analog Output
24
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相關PDF資料 |
PDF描述 |
|---|---|
| A1374EKB-T | IC SENSOR HALL EFFECT PREC 3-SIP |
| A1422LK | IC SENSOR HALL EFFECT AC 4-SIP |
| A1425LK | IC SENSOR HALL EFFECT AC 4-SIP |
| A1645LK-I2 | IC SENSOR HALL EFFECT AC 4-SIP |
| A3230LUA-T | IC SW HALL EFFECT CHOPPER 3-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1362LKTTN-T | 功能描述:IC HALL EFFECT SENSOR LN 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1363LKTTN-10-T | 功能描述:IC HALL SENSOR 6.4-14MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
| A1363LKTTN-1-T | 功能描述:IC HALL SENSOR 0.6-1.3MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:模塊 標準包裝:1 |
| A1363LKTTN-2-T | 功能描述:IC HALL SENSOR 1.3-2.9MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
| A1363LKTTN-5-T | 功能描述:IC HALL SENSOR 2.9-6.4MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。