- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1244LUA-I2-T (Allegro Microsystems Inc)IC HALL EFFECT LATCH SIP-3 Datasheet資料下載
參數資料
| 型號： | A1244LUA-I2-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 253K |
| 描述： | IC HALL EFFECT LATCH SIP-3 |
| 標準包裝： | 4,000 |
| 傳感范圍： | 80G 跳閘，-80G 釋放 |
| 類型： | 雙極卡鎖 |
| 電源電壓： | 3 V ~ 24 V |
| 電流 - 電源： | 5mA |
| 輸出類型： | 數字 |
| 特點： | 高速度 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 3-SSIP |
| 供應商設備封裝： | 3-SIP |
| 包裝： | 散裝 |
| 其它名稱： | 620-1424 |
Chopper-Stabilized, Two Wire
Hall-Effect Latch
A1244
9
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
The device must be operated below the maximum junction tem-
perature of the device, T
J
(max). Under certain combinations of
peak conditions, reliable operation may require derating supplied
power or improving the heat dissipation properties of the appli-
cation. This section presents a procedure for correlating factors
affecting operating T
J
. (Thermal data is also available on the
Allegro MicroSystems Web site.)
The Package Thermal Resistance, R
qJA
, is a figure of merit sum-
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity, K,
of the printed circuit board, including adjacent devices and traces.
Radiation from the die through the device case, R
qJC
, is relatively
small component of R
qJA
. Ambient air temperature, T
A
, and air
motion are significant external factors, damped by overmolding.
The effect of varying power levels (Power Dissipation, P
D
), can
be estimated. The following formulas represent the fundamental
relationships used to estimate T
J
, at P
D
.
P
D
= V
IN
?/DIV>
I
IN
(1)
DT = P
D
?/DIV>
R
qJA
(2)
T
J
= T
A
+ 擳
(3)
For example, given common conditions such as: T
A
= 25癈,
V
CC
= 12 V, I
CC
= 4 mA, and R
qJA
= 140 癈/W, then:
P
D
= V
CC
?/DIV>
I
CC
= 12 V
?/DIV>
4 mA = 48 mW
DT = P
D
?/DIV>
R
qJA
= 48 mW
?/DIV>
140 癈/W = 7癈
T
J
= T
A
+ DT = 25癈 + 7癈 = 32癈
A worst-case estimate, P
D
(max), represents the maximum allow-
able power level (V
CC
(max), I
CC
(max)), without exceeding
T
J
(max), at a selected R
qJA
and T
A
.
Example: Reliability for V
CC
at T
A
=
150癈, package LH, using a
low-K PCB.
Observe the worst-case ratings for the device, specifically:
R
qJA
=
110 癈/W, T
J
(max)
=
165癈, V
CC
(max)
=
24 V, and
I
CC
(max)
=
17
mA.
Calculate the maximum allowable power level, P
D
(max). First,
invert equation 3:
DT
max
= T
J
(max) T
A
= 165
癈
150
癈 = 15
癈
This provides the allowable increase to T
J
resulting from internal
power dissipation. Then, invert equation 2:
P
D
(max)
= DT
max
?R
qJA
= 15癈 ?110 癈/W = 136 mW
Finally, invert equation 1 with respect to voltage:
V
CC(est)
= P
D
(max)
? I
CC
(max) = 136 mW ?17 mA = 8 V
The result indicates that, at T
A
, the application and device can
dissipate adequate amounts of heat at voltages dV
CC(est)
.
Compare V
CC(est)
to V
CC
(max). If V
CC(est)
d V
CC
(max), then reli-
able operation between V
CC(est)
and V
CC
(max) requires enhanced
R
qJA
. If V
CC(est)
e V
CC
(max), then operation between V
CC(est)
and V
CC
(max) is reliable under these conditions.
Power Derating
相關PDF資料 |
PDF描述 |
|---|---|
| A1302KUA-T | IC SENSOR HALL EFFECT 3-SIP |
| A1323LLHLT-T | IC SENSOR HALL EFFECT SOT23W |
| A1351LKTTN-T | IC SENSOR HALL EFFECT 4-SIP |
| A1354KKT-T | IC SENSOR HALL EFFECT 4-SIP |
| A1356LKB-T | IC SENSOR HALL EFFECT 3 SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1245LLHLT-I1-T | 功能描述:IC HALL EFFECT LATCH SOT23-3 制造商:allegro microsystems, llc 系列:- 包裝:帶卷（TR） 零件狀態:有效 功能:卡銷 技術:霍爾效應 極化:南極 感應范圍:4mT 跳閘，-4mT 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:3 V ~ 24 V 電流 - 電源（最大值）:6.9mA 電流 - 輸出（最大值）:- 輸出類型:開路漏極 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商器件封裝:SOT-23-3 標準包裝:3,000 |
| A1245LLHLT-I2-T | 功能描述:IC HALL EFFECT LATCH SOT23-3 制造商:allegro microsystems, llc 系列:- 包裝:帶卷（TR） 零件狀態:有效 功能:卡銷 技術:霍爾效應 極化:南極 感應范圍:4mT 跳閘，-4mT 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:3 V ~ 24 V 電流 - 電源（最大值）:5mA 電流 - 輸出（最大值）:- 輸出類型:開路漏極 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商器件封裝:SOT-23-3 標準包裝:3,000 |
| A1245LLHLX-I1-T | 功能描述:IC HALL EFFECT LATCH SOT23-3 制造商:allegro microsystems, llc 系列:- 包裝:帶卷（TR） 零件狀態:有效 功能:卡銷 技術:霍爾效應 極化:南極 感應范圍:4mT 跳閘，-4mT 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:3 V ~ 24 V 電流 - 電源（最大值）:6.9mA 電流 - 輸出（最大值）:- 輸出類型:開路漏極 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商器件封裝:SOT-23-3 標準包裝:10,000 |
| A1245LLHLX-I2-T | 功能描述:IC HALL EFFECT LATCH SOT23-3 制造商:allegro microsystems, llc 系列:- 包裝:帶卷（TR） 零件狀態:有效 功能:卡銷 技術:霍爾效應 極化:南極 感應范圍:4mT 跳閘，-4mT 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:3 V ~ 24 V 電流 - 電源（最大值）:5mA 電流 - 輸出（最大值）:- 輸出類型:開路漏極 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商器件封裝:SOT-23-3 標準包裝:10,000 |
| A1245LUA-I1-T | 功能描述:IC HALL EFFECT LATCH 3SIP 制造商:allegro microsystems, llc 系列:- 包裝:散裝 零件狀態:有效 功能:卡銷 技術:霍爾效應 極化:南極 感應范圍:4mT 跳閘，-4mT 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:3 V ~ 24 V 電流 - 電源（最大值）:6.9mA 電流 - 輸出（最大值）:- 輸出類型:開路漏極 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:3-SIP 模塊 供應商器件封裝:3-SIP 標準包裝:500 |
發布緊急采購，3分鐘左右您將得到回復。