- 您現在的位置：買賣IC網 > PDF目錄375099 > A1185LLHLT-T (Allegro MicroSystems, Inc.) Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches PDF資料下載
參數資料
| 型號： | A1185LLHLT-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| 中文描述： | 超靈敏雙線現場可編程斬波穩定單極霍爾效應開關 |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 318K |
| 代理商： | A1185LLHLT-T |
10
A1185-DS, Rev. 1
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall Effect Switches
A1185 and A1186
PROGRAMMING PROTOCOL CHARACTERISTICS
, over operating temperature range, unless otherwise noted
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Programming Voltage
1
V
PL
Minimum voltage range during programming
4.5
5.0
5.5
V
V
PM
11.5
12.5
13.5
V
V
PH
25
26
27
V
Programming Current
2
I
PP
t
r
= 11
μ
s; 5 V
→
26 V; C
BYP
= 0.1
μ
F
-
190
-
mA
Pulse Width
t
d(0)
OFF time between programming bits
20
-
-
μ
s
t
d(1)
Pulse duration for enable and addressing
sequences
20
-
-
μ
s
t
d(P)
Pulse duration for fuse blowing
100
300
-
μ
s
Pulse Rise Time
t
r
V
PL
to V
PM
;
V
PL
to V
PH
5
-
20
μ
s
Pulse Fall Time
t
f
V
PM
to V
PL
; V
PH
to V
PL
5
-
100
μ
s
1
Programming voltages are measured at the VCC pin.
2
A bypass capacitor with a minimum capacitance of 0.1
μ
F must be connected from VCC to the GND pin of the A118x device in order to
provide the current necessary to blow the fuse.
V
PH
V+
t
V
PM
V
PL
0
T
d(1)
T
d(0)
T
d(P)
Figure 4. Pulse amplitudes and durations
Additional information on device programming and program-
ming products is available on www. allegromicro.com. Program-
ming hardware is available for purchase, and programming
software is available free of charge.
Programming Protocol
The operate switchpoint, B
OP
, can be field-programmed. To do
so, a coded series of voltage pulses through the VCC pin is used
to set bitfields in onboard registers. The effect on the device
output can be monitored, and the registers can be cleared and
set repeatedly until the required B
OP
is achieved. To make the
setting permanent, bitfield-level solid state fuses are blown, and
finally, a device-level fuse is blown, blocking any further cod-
ing. It is not necessary to program the release switchpoint, B
RP
,
because the difference between B
OP
and B
RP
, referred to as the
hysteresis, B
HYS
, is fixed.
The range of values between B
OP(min)
and B
OP(max)
is scaled to
31 increments. The actual change in magnetic flux (G) repre-
sented by each increment is indicated by B
RES
(see the Operating
Characteristics table; however, testing is the only method for
verifying the resulting B
OP
). For programming, the 31 incre-
ments are individually identified using 5 data bits, which are
physically represented by 5 bitfields in the onboard registers.
By setting these bitfields, the corresponding calibration value is
programmed into the device.
Three voltage levels are used in programming the device: a low
voltage, V
PL
, a minimum required to sustain register settings; a
mid-level voltage, V
PM
, used to increment the address counter
in the device; and a high voltage, V
PH
, used to separate sets of
V
PM
pulses (when short in duration) and to blow fuses (when
long in duration). A fourth voltage level, essentially 0 V, is used
to clear the registers between pulse sequences. The pulse values
are shown in the Programming Protocol Characteristics table and
in figure 4.
Code Programming.
Each bitfield must be individually set. To
do so, a pulse sequence must be transmitted for each bitfield that
is being set to 1. If more than one bitfield is being set to 1, all
pulse sequences must be sent, one after the other, without allow-
ing V
CC
to fall to zero (which clears the registers).
The same pulse sequence is used to provisionally set bitfields as
is used to permanently set bitfield-level fuses. The only differ-
ence is that when provisionally setting bitfields, no fuse-blowing
pulse is sent at the end of the pulse sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| A1185LUA | RES MF 24.3K OHM 1%0.250W@ 70C 100PPM/TC AXL |
| A1185LUA-T | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1186 | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1186EUA | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1186EUA-T | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1185LUA | 功能描述:IC SWITCH HALL EFFECT UNI 3-SIP RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1185LUA-T | 功能描述:IC SWITCH HALL EFFECT UNI 3-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1186 | 制造商:Quick 功能描述:TSOJ 18mm x 10mm Nozzle for 21-13205 and 21-13210 制造商:QUICK 功能描述:TSOJ 18 X 10 NOZZLE FOR QUICK957/957D |
| A118-6 | 功能描述:SWITCH HARDWARE RoHS:是 類別:開關 >> 配件 - 帽蓋 系列:800 標準包裝:1 系列:AP 開關類型:按鈕 形狀:圓形，凸起（圓頂） 顏色:紅 發光:發光開口 適用于相關產品:AP 系列 安裝類型:卡入式 尺寸:12.35mm 直徑 x 6.25mm H 特點:- 配用:AP2N006TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N003TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N002TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N006SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N003SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N002SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP4N007SWBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N007TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP2N007SZBE-ND - SWITCH PUSH SPST-NO 0.125A 125VAP4N006TZBE-ND - SWITCH PUSH SPST-NO 0.125A 125V更多... 其它名稱:*481D03001 |
| A1186ELHLT | 功能描述:IC SWITCH HALL EFFECT UNI SOT-23 RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。