- 您現在的位置：買賣IC網 > PDF目錄375099 > A1185 (Allegro MicroSystems, Inc.) Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches PDF資料下載
參數資料
| 型號： | A1185 |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| 中文描述： | 超靈敏雙線現場可編程斬波穩定單極霍爾效應開關 |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 318K |
| 代理商： | A1185 |
12
A1185-DS, Rev. 1
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall Effect Switches
A1185 and A1186
V
PH
V+
t
V
PM
V
PL
0
Address 1
Address 2
Address
n
(
≤
31)
Figure 8. Pulse sequence to select addresses
Falling edge of final B
OP
address digit
V
PH
V+
t
V
PM
V
PL
0
Encode Lock Bit
Enable
Address
Blow
32 pulses
Figure 9. Pulse sequence to encode lock bit
Lock Bit Programming
.
After the desired B
OP
calibration value
is programmed, and all of the corresponding bitfield-level fuses
are blown, the device-level fuse should be blown. To do so, the
lock bit (bitfield address 32) should be encoded as 1 and have
its fuse blown. This is done in the same manner as permanently
setting the other bitfields, as shown in figure 9.
Enabling Addressing Mode
.
The first segment of code is a
keying sequence used to enable the bitfield addressing mode. As
shown in figure 7, this segment consists of one short V
PH
pulse,
one V
PM
pulse, and one short V
PH
pulse, with no supply inter-
ruptions. This sequence is designed to prevent the device from
being programmed accidentally, such as by noise on the supply
line.
Figure 7. Addressing mode enable pulse sequence
V
PH
V+
t
V
PM
V
PL
0
Address Selection
.
After addressing mode is enabled, the
target bitfield address, is indicated by a series of V
PM
pulses, as
shown in figure 8.
相關PDF資料 |
PDF描述 |
|---|---|
| A1185EUA-T | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1185LLHLT-T | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1185LUA | RES MF 24.3K OHM 1%0.250W@ 70C 100PPM/TC AXL |
| A1185LUA-T | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1186 | Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A118-5 | 制造商:APEM 功能描述: |
| A1185_06 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1185B | 制造商:HAKKO Corporation 功能描述: |
| A1185ELHLT | 功能描述:IC SWITCH HALL EFFECT UNI SOT-23 RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1185ELHLT-T | 功能描述:IC SWITCH HALL EFFECT UNI SOT-23 RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。