- 您現在的位置：買賣IC網 > Datasheet目錄59 > A1184LUA-T (Allegro Microsystems Inc)IC SWITCH HALL EFFECT UNI 3-SIP Datasheet資料下載
參數資料
| 型號： | A1184LUA-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 13/15頁 |
| 文件大小： | 487K |
| 描述： | IC SWITCH HALL EFFECT UNI 3-SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 500 |
| 傳感范圍： | 300G ~ 600G - 可編程，固定釋放 |
| 類型： | 單極開關 |
| 電源電壓： | 3.5 V ~ 24 V |
| 電流 - 電源： | 6.9mA |
| 輸出類型： | 數字式，差分 |
| 特點： | 可編程 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 3-SIP |
| 供應商設備封裝： | 3-SIP |
| 包裝： | 散裝 |
Standard Two-Wire Field-Programmable
Chopper-Stabilized Unipolar Hall Effect Switch
A1184
12
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
V
PH
V+
t
V
PM
V
PL
0
Address 1
Address 2
Address n ( d 31)
Figure 8. Pulse sequence to select addresses
Falling edge of final B
OP
address digit
V
PH
V+
t
V
PM
V
PL
0
Encode Lock Bit
Enable
Address
Blow
32 pulses
Figure 9. Pulse sequence to encode lock bit
Lock Bit Programming. After the desired B
OP
calibration value
is programmed, and all of the corresponding bitfield-level fuses
are blown, the device-level fuse should be blown. To do so, the
lock bit (bitfield address 32) should be encoded as 1 and have
its fuse blown. This is done in the same manner as permanently
setting the other bitfields, as shown in figure 9.
Figure 7. Addressing mode enable pulse sequence
V
PH
V+
t
V
PM
V
PL
0
Enabling Addressing Mode. The first segment of code is a
keying sequence used to enable the bitfield addressing mode. As
shown in figure 7, this segment consists of one short V
PH
pulse,
one V
PM
pulse, and one short V
PH
pulse, with no supply inter-
ruptions. This sequence is designed to prevent the device from
being programmed accidentally, such as by noise on the supply
line.
Address Selection. After addressing mode is enabled, the
target bitfield address, is indicated by a series of V
PM
pulses, as
shown in figure 8.
相關PDF資料 |
PDF描述 |
|---|---|
| A1186LUA-T | IC SWITCH HALL EFFECT UNI 3-SIP |
| A1193LUA-T | IC SW HALL EFFECT CHOPPER 3SIP |
| A1203LUA-T | IC SW CONTINUOUS TIME BIPO 3-SIP |
| A1205EUA-T | IC SWITCH HALL EFFECT GP 3-SIP |
| A1211LUA-T | IC LATCH HALL EFFECT 3-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1185 | 制造商:Quick 功能描述:TSOJ 13 X 10 NOZZLE FOR QUICK957/957D |
| A118-5 | 制造商:APEM 功能描述: |
| A1185_06 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1185B | 制造商:HAKKO Corporation 功能描述: |
| A1185ELHLT | 功能描述:IC SWITCH HALL EFFECT UNI SOT-23 RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。