- 您現在的位置：買賣IC網 > PDF目錄375097 > A1140LUATI-T4 (Allegro MicroSystems, Inc.) Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches PDF資料下載
參數資料
| 型號： | A1140LUATI-T4 |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
| 中文描述： | 敏感的兩線斬波穩定單極霍爾效應開關 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 354K |
| 代理商： | A1140LUATI-T4 |
Sensitive Two-Wire Chopper-Stabilized
Unipolar Hall Effect Switches
A1140, A1141,
A1142, and A1143
8
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Chopper Stabilization Technique
When using Hall-effect technology, a limiting factor for
switchpoint accuracy is the small signal voltage developed
across the Hall element. This voltage is disproportionally small
relative to the offset that can be produced at the output of the
Hall sensor. This makes it difficult to process the signal while
maintaining an accurate, reliable output over the specified oper-
ating temperature and voltage ranges.
Chopper stabilization is a unique approach used to minimize
Hall offset on the chip. The patented Allegro technique, namely
Dynamic Quadrature Offset Cancellation, removes key sources
of the output drift induced by thermal and mechanical stresses.
This offset reduction technique is based on a signal modulation-
demodulation process. The undesired offset signal is separated
from the magnetic field-induced signal in the frequency domain,
through modulation. The subsequent demodulation acts as a
modulation process for the offset, causing the magnetic field-
induced signal to recover its original spectrum at baseband, while
the dc offset becomes a high-frequency signal. The magnetic-
sourced signal then can pass through a low-pass filter, while the
modulated dc offset is suppressed. This configuration is illus-
trated in figure 2.
The chopper stabilization technique uses a 200 kHz high
frequency clock. For demodulation process, a sample and hold
technique is used, where the sampling is performed at twice the
chopper frequency (400 kHz). This high-frequency operation
allows a greater sampling rate, which results in higher accuracy
and faster signal-processing capability. This approach desensi-
tizes the chip to the effects of thermal and mechanical stresses,
and produces devices that have extremely stable quiescent Hall
output voltages and precise recoverability after temperature
cycling. This technique is made possible through the use of a
BiCMOS process, which allows the use of low-offset, low-noise
amplifiers in combination with high-density logic integration
and sample-and-hold circuits.
The repeatability of magnetic field-induced switching is affected
slightly by a chopper technique. However, the Allegro high-
frequency chopping approach minimizes the affect of jitter and
makes it imperceptible in most applications. Applications that
are more likely to be sensitive to such degradation are those
requiring precise sensing of alternating magnetic fields; for
example, speed sensing of ring-magnet targets. For such applica-
tions, Allegro recommends its digital sensor families with lower
sensitivity to jitter. For more information on those devices,
contact your Allegro sales representative.
Figure 2. Chopper stabilization circuit (Dynamic Quadrature Offset Cancellation)
Amp
Regulator
Clock/Logic
Hall Element
S
H
Low-Pass
Filter
相關PDF資料 |
PDF描述 |
|---|---|
| A1141 | Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
| A1141EUATI-T4 | Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
| A1141LUATI-T4 | Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
| A1142 | Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
| A1142ELHLT-T | Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1141 | 制造商:Quick 功能描述:PLCC 11.5 X 14 NOZZLE FOR QUICK957/957D |
| A114106 | 制造商:NORTH SAFETY PRODUCTS 功能描述:HELMET FULL FACE WITH FACE SEAL. |
| A-1141-1 | 功能描述:通用繼電器 DC SOLENOID. RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料: |
| A114132A1NCRB | 制造商:C&K Components 功能描述:SP,90,2POS,HI,NON SHORT,PC THRU,BULK - Bulk 制造商:C&K Components 功能描述:Switch Key Lock SPDT 90° Flat Key 20VAC 20VDC 0.4VA PC Pins Thru-Hole |
| A114132A1NCRQ | 功能描述:鍵鎖開關 Switchlocks RoHS:否 制造商:C&K Components 觸點形式:1 Form A (SPST-NO) 開關功能:Momentary 觸點額定值: 電流額定值:100 mA 電壓額定值 AC:250 VAC 端接類型:Through Hole 鍵類型:Keyswitch 變址: 位置數量:1 外殼材料: |
發布緊急采購，3分鐘左右您將得到回復。