- 您現在的位置：買賣IC網 > PDF目錄375097 > A1106 (Allegro MicroSystems, Inc.) KPTC 3C 3#20 SKT RECP PDF資料下載
參數資料
| 型號： | A1106 |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | KPTC 3C 3#20 SKT RECP |
| 中文描述： | 連續時間開關系列 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 428K |
| 代理商： | A1106 |
9
A1101-DS
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Continuous-Time Switch Family
A1101, A1102, A1103, A1104, and A1106
Power Derating
Power Derating
The device must be operated below the maximum junction
temperature of the device, T
J(max)
. Under certain combinations of
peak conditions, reliable operation may require derating sup-
plied power or improving the heat dissipation properties of the
application. This section presents a procedure for correlating
factors affecting operating T
J
. (Thermal data is also available on
the Allegro MicroSystems Web site.)
The Package Thermal Resistance, R
θ
JA
, is a figure of merit sum-
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity,
K, of the printed circuit board, including adjacent devices and
traces. Radiation from the die through the device case, R
θ
JC
, is
relatively small component of R
θ
JA
. Ambient air temperature,
T
A
, and air motion are significant external factors, damped by
overmolding.
The effect of varying power levels (Power Dissipation, P
D
), can
be estimated. The following formulas represent the fundamental
relationships used to estimate T
J
, at P
D
.
P
D
= V
IN
×
I
IN
(1)
T = P
D
×
R
θ
JA
(2)
T
J
= T
A
+
T
(3)
For example, given common conditions such as: T
A
= 25°C,
V
CC
= 12 V, I
CC
= 4 mA, and R
θ
JA
= 140 °C/W, then:
P
D
= V
CC
×
I
CC
= 12 V
×
4 mA = 48 mW
T = P
D
×
R
θ
JA
= 48 mW
×
140 °C/W = 7°C
T
J
= T
A
+
T = 25°C + 7°C = 32°C
A worst-case estimate, P
D(max)
, represents the maximum allow-
able power level (V
CC(max)
, I
CC(max)
), without exceeding T
J(max)
,
at a selected R
θ
JA
and T
A
.
Example
: Reliability for V
CC
at T
A
=
150°C, package UA, using
minimum-K PCB.
Observe the worst-case ratings for the device, specifically:
R
θ
JA
=
165°C/W, T
J(max)
=
165°C, V
CC(max)
=
24 V, and
I
CC(max)
=
7.5
mA.
Calculate the maximum allowable power level, P
D(max)
. First,
invert equation 3:
T
max
= T
J(max)
– T
A
= 165
°C
–
150
°C = 15
°C
This provides the allowable increase to T
J
resulting from internal
power dissipation. Then, invert equation 2:
P
D(max)
=
T
max
÷ R
θ
JA
= 15°C ÷ 165 °C/W = 91 mW
Finally, invert equation 1 with respect to voltage:
V
CC(est)
= P
D(max)
÷ I
CC(max)
= 91 mW ÷ 7.5 mA = 12.1 V
The result indicates that, at T
A
, the application and device can
dissipate adequate amounts of heat at voltages
≤
V
CC(est)
.
Compare V
CC(est)
to V
CC(max)
. If V
CC(est)
≤
V
CC(max)
, then reli-
able operation between V
CC(est)
and V
CC(max)
requires enhanced
R
θ
JA
. If V
CC(est)
≥
V
CC(max)
, then operation between V
CC(est)
and
V
CC(max)
is reliable under these conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| A1106EUA-T | Continuous-Time Switch Family |
| A1106LLHLT-T | Continuous-Time Switch Family |
| A1102LUA-T | Continuous-Time Switch Family |
| A1103ELHLT-T | Continuous-Time Switch Family |
| A1112 | A1112 High-Power 1550 nm DFB Source Lasers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1106.0 | 制造商:DORMER 功能描述:DRILL LS HSS 6MM |
| A1106.0- | 制造商:ROEBUCK 功能描述:RBK HSS L/S DRILL 6.00MM |
| A1106.5 | 制造商:DORMER 功能描述:DRILL LS HSS 6.5MM 制造商:DORMER 功能描述:DRILL, LS, HSS, 6.5MM |
| A1106.8 | 制造商:DORMER 功能描述:DRILL LS HSS 6.8MM |
| A1-106-001-001 | 制造商:n/a 功能描述:Thyristor Module |
發布緊急采購，3分鐘左右您將得到回復。