參數資料
    型號: A10305MSZQF
    廠商: ITT CANNON
    元件分類: 開關
    英文描述: ROTARY SWITCH-3POSITIONS, SP3T, LATCHED, 0.35A, 125VDC, PANEL MOUNT-THREADED
    封裝: ROHS COMPLIANT
    文件頁數: 5/5頁
    文件大小: 338K
    代理商: A10305MSZQF
    L–7
    L
    Rotary
    C&K A Series
    1-4 Pole Rotary Switches
    FUNCTION
    AVAILABLE HARDWARE
    SPLASHPROOF
    BUSHING SEAL
    (FIG. 1)
    (FIG. 2)
    (FIG. 3)
    REMOVABLE CLIP
    LOCATING
    TAB
    STANDOFF
    K EPOXY & SPLASHPROOF BUSHING SEAL
    F SPLASHPROOF BUSHING SEAL
    NONE NO SEAL
    E
    EPOXY SEAL
    Stop ring
    PART NO.
    767B00201
    Material: Brass
    Finish: Nickel plated
    Setting Stops on A112 and A125 Models
    The number of switch positions is adjustable on A112
    and A125 models only by means of a stop ring provided
    with each switch. The number of positions is pre-set on
    all other models and the stop ring is factory installed.
    Soldering
    1. Insert switch base only into PC board.
    2. Do not bend terminals.
    3. Wave soldering recommended at
    500F solder temperature.
    4. Hand solder at 500F, 10 sec.
    max./terminal.
    Switch Assembly
    1. Hold housing/shaft assembly by housing. Remove
    protective cap by squeezing tabs and discard. (FIG. 1)
    2. Do not push on switch shaft. Detent mechanism will
    come apart.
    3. While holding switch housing, align locating tab on
    base with notch on housing and engage 4 housing
    latches in slots on base. (FIG. 2)
    4. Push firmly on housing until latches snap in place.
    5. Remove clip from shaft and discard. Assembly is
    complete. (FIG. 3)
    Cleaning
    1. Flux clean using vapor degreaser and forced
    rinse or triple bath method.
    2. Do not allow switch base to ‘trap’ fluids.
    3. Freon TMC, TF or Methylene Chloride give
    excellent results.
    To set stops: Turn shaft fully counter-clockwise and
    insert stop ring tab in desired hole. Install lockwasher
    and nut to retain stop ring for both PC and panel
    mounting. Switch without stop ring has 12 positions.
    Soldering, Cleaning and Assembly Instructions for ‘MC’ Termination Option
    Dimensions are shown: Inch (mm)
    Specifications and dimensions subject to change
    www.ittcannon.com
    相關PDF資料
    PDF描述
    A112S1RNCGK ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT
    A112S1RNZG ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.35A, 125VDC, PANEL MOUNT-THREADED
    A11042RNMCQE ROTARY SWITCH-10POSITIONS, SP10T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT
    A100S1MSZBK ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.02A, 20VDC, PANEL MOUNT-THREADED
    A10515RNMCQE ROTARY SWITCH-5POSITIONS, SP5T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT
    相關代理商/技術參數
    參數描述
    A10305RNCB 功能描述:旋鈕開關 Rotary RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver
    A10305RNCBE 功能描述:旋鈕開關 Rotary RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver
    A10305RNCG 功能描述:旋鈕開關 Rotary RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver
    A10305RNCGF 功能描述:旋鈕開關 Rotary RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver
    A10305RNCQ 功能描述:旋鈕開關 Rotary RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver