(W or s t - C as e M i l i t a r y Cond i t i o n s , V <" />
參數資料
型號: A1010B-1PQG100I
廠商: Microsemi SoC
文件頁數: 20/98頁
文件大?。?/td> 0K
描述: IC FPGA 1200 GATES 100-PQFP IND
標準包裝: 66
系列: ACT™ 1
LAB/CLB數: 295
輸入/輸出數: 57
門數: 1200
電源電壓: 4.5 V ~ 5.5 V
安裝類型: 表面貼裝
工作溫度: -40°C ~ 85°C
封裝/外殼: 100-BQFP
供應商設備封裝: 100-PQFP(14x20)
27
Hi R e l F P GA s
A1 24 0A T i m i n g C har a c t e r i st i c s
(W or s t - C as e M i l i t a r y Cond i t i o n s , V CC = 4.5 V, TJ = 1 25°C)
‘–1’ Speed
‘Std’ Speed
Parameter
Description
Min.
Max.
Min.
Max.
Units
Logic Module Propagation Delays1
tPD1
Single Module
5.2
6.1
ns
tCO
Sequential Clk to Q
5.2
6.1
ns
tGO
Latch G to Q
5.2
6.1
ns
tRS
Flip-Flop (Latch) Reset to Q
5.2
6.1
ns
Logic Module Predicted Routing Delays2
tRD1
FO=1 Routing Delay
1.9
2.2
ns
tRD2
FO=2 Routing Delay
2.4
2.8
ns
tRD3
FO=3 Routing Delay
3.1
3.7
ns
tRD4
FO=4 Routing Delay
4.3
5.0
ns
tRD8
FO=8 Routing Delay
6.6
7.7
ns
Logic Module Sequential Timing3, 4
tSUD
Flip-Flop (Latch) Data Input Setup
0.5
ns
tHD
Flip-Flop (Latch) Data Input Hold
0.0
ns
tSUENA
Flip-Flop (Latch) Enable Setup
1.3
ns
tHENA
Flip-Flop (Latch) Enable Hold
0.0
ns
tWCLKA
Flip-Flop (Latch) Clock Active Pulse
Width
7.4
8.1
ns
tWASYN
Flip-Flop (Latch) Asynchronous Pulse
Width
7.4
8.1
ns
tA
Flip-Flop Clock Input Period
14.8
18.6
ns
tINH
Input Buffer Latch Hold
2.5
ns
tINSU
Input Buffer Latch Setup
–3.5
ns
tOUTH
Output Buffer Latch Hold
0.0
ns
tOUTSU
Output Buffer Latch Setup
0.5
ns
fMAX
Flip-Flop (Latch) Clock Frequency
63
54
MHz
Notes:
1.
For dual-module macros, use tPD1 + tRD1 + tPDn , tCO + tRD1 + tPDn , or tPD1 + tRD1 + tSUD , whichever is appropriate.
2.
Routing delays are for typical designs across worst-case operating conditions. These parameters should be used for estimating device
performance. Post-route timing analysis or simulation is required to determine actual worst-case performance. Post-route timing is based
on actual routing delay measurements performed on the device prior to shipment.
3.
Data applies to macros based on the S-module. Timing parameters for sequential macros constructed from C-modules can be obtained from
the DirectTime Analyzer utility.
4.
Setup and hold timing parameters for the Input Buffer Latch are defined with respect to the PAD and the D input. External setup/hold
timing parameters must account for delay from an external PAD signal to the G inputs. Delay from an external PAD signal to the G input
subtracts (adds) to the internal setup (hold) time.
相關PDF資料
PDF描述
M7A3P1000-1FG256 IC FPGA 1KB FLASH 1M 256-FBGA
A3PE600-2FG256I IC FPGA 600000 GATES 256-FBGA
A3PE600-2FGG256I IC FPGA 600000 GATES 256-FBGA
A42MX09-3PL84 IC FPGA MX SGL CHIP 14K 84-PLCC
AMC08DTEH CONN EDGECARD 16POS .100 EYELET
相關代理商/技術參數
參數描述
A1010B-1VQ80C 功能描述:IC FPGA 1200 GATES 80-VQFP COM RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:ACT™ 1 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA(27X27)
A1010B-1VQ80I 功能描述:IC FPGA 1200 GATES 80-VQFP IND RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:ACT™ 1 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA(27X27)
A1010B-1VQ84B 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ACT 1 Series FPGAs
A1010B-1VQ84C 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ACT 1 Series FPGAs
A1010B-1VQ84I 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ACT 1 Series FPGAs