- 您現在的位置：買賣IC網 > PDF目錄24802 > 935287979518 (NXP SEMICONDUCTORS) DATACOM, INTERFACE CIRCUIT, PDSO14 PDF資料下載
參數資料
| 型號： | 935287979518 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 網絡接口 |
| 英文描述： | DATACOM, INTERFACE CIRCUIT, PDSO14 |
| 封裝： | 3.90 MM, PLASTIC, MS-012, SOT108-1, SOP-14 |
| 文件頁數： | 27/28頁 |
| 文件大?。?/td> | 281K |
| 代理商： | 935287979518 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁
TJA1054_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 24 September 2009
8 of 25
NXP Semiconductors
TJA1054
Fault-tolerant CAN transceiver
A local wake-up through pin WAKE is detected by a rising or falling edge with a
consecutive level exceeding the maximum specied tWAKE.
On a wake-up request the transceiver will set the output on pin INH to HIGH which can be
used to activate the external supply voltage regulator.
If VCC is provided the wake-up request can be read on the ERR or RXD outputs, so the
external microcontroller can activate the transceiver (switch to normal operating mode) via
pins STB and EN.
To prevent a false remote wake-up due to transients or RF elds, the wake-up voltage
levels have to be maintained for a certain period of time. In the low power modes the
failure detection circuit remains partly active to prevent an increased power consumption
in the event of failures 3, 3a, 4 and 7.
To prevent a false local wake-up during an open wire at pin WAKE, this pin has a weak
pull-up current source towards VBAT. However, in order to prevent EMC issues, it is
recommended to connect a not used pin WAKE to pin BAT. INH is set to oating only if
the goto-sleep command is entered successfully. To enter a successful goto-sleep
command under all conditions, this command must be kept stable for the maximum
specied th(sleep).
Pin INH will be set to a HIGH level again by the following events only:
VBAT power-on (cold start)
Rising or falling edge on pin WAKE
A message frame with a dominant phase of at least the maximum specied t(CANH) or
t(CANL), while pin EN or pin STB is at a LOW level
Pin STB goes to a HIGH level with VCC active
To provide fail-safe functionality, the signals on pins STB and EN will internally be set to
LOW when VCC is below a certain threshold voltage (VCC(stb)).
7.3 Power-on
After power-on (VBAT switched on) the signal on pin INH will become HIGH and an internal
power-on ag will be set. This ag can be read in the power-on standby mode through
pin ERR (STB = 1; EN = 0) and will be reset by entering the normal operating mode.
7.4 Protections
A current limiting circuit protects the transmitter output stages against short-circuit to
positive and negative battery voltage.
If the junction temperature exceeds the typical value of 165
°C, the transmitter output
stages are disabled. Because the transmitter is responsible for the major part of the power
dissipation, this will result in a reduced power dissipation and hence a lower chip
temperature. All other parts of the device will continue to operate.
The pins CANH and CANL are protected against electrical transients which may occur in
an automotive environment.
相關PDF資料 |
PDF描述 |
|---|---|
| 935287981512 | DATACOM, INTERFACE CIRCUIT, PDSO14 |
| 935287981518 | DATACOM, INTERFACE CIRCUIT, PDSO14 |
| 07488-01100 | EINPRESSMUTTERN KIT |
| 07488-09470 | M3 EINSAETZE |
| 07488-09500 | M6 EINSAETZE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935288287551 | 制造商:NXP Semiconductors 功能描述:- Trays |
| 935288287557 | 制造商:NXP Semiconductors 功能描述:- Trays |
| 935288465027 | 制造商:NXP Semiconductors 功能描述:IC SMARTCARD RTC OSC COUNTER |
| 935288948115 | 制造商:NXP Semiconductors 功能描述:IC ANALOG SWITCH SP3T 10XQFN |
| 935288949115 | 制造商:NXP Semiconductors 功能描述:IC ANALOG SWITCH SPDT 10XQFN |
發布緊急采購，3分鐘左右您將得到回復。