參數資料
型號： 935270051518
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68
封裝： PLASTIC, MS-018, SOT-188-2, LCC-68
文件頁數： 16/55頁
文件大?。?/td> 706K
代理商： 935270051518
Philips Semiconductors
SC16C654/654D
Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 02 — 13 March 2003
23 of 52
9397 750 10985
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive
FIFO trigger levels, and select the DMA mode.
7.3.1
DMA mode
Mode 0 (FCR bit 3 = 0): Set and enable the interrupt for each single transmit or
receive operation, and is similar to the 16C454 mode. Transmit Ready (TXRDY) will
go to a logic 0 whenever an empty transmit space is available in the Transmit Holding
Register (THR). Receive Ready (RXRDY) will go to a logic 0 whenever the Receive
Holding Register (RHR) is loaded with a character.
Mode 1 (FCR bit 3 = 1): Set and enable the interrupt in a block mode operation. The
transmit interrupt is set when the transmit FIFO is below the programmed trigger
level. TXRDY remains a logic 0 as long as one empty FIFO location is available. The
receive interrupt is set when the receive FIFO lls to the programmed trigger level.
However, the FIFO continues to ll regardless of the programmed level until the FIFO
is full. RXRDY remains a logic 0 as long as the FIFO ll level is above the
programmed trigger level.
7.3.2
FIFO mode
Table 10:
FIFO Control Register bits description
Bit
Symbol
Description
7-6
FCR[7]
(MSB),
FCR[6]
(LSB)
RCVR trigger. These bits are used to set the trigger level for the receive
FIFO interrupt.
An interrupt is generated when the number of characters in the FIFO
equals the programmed trigger level. However, the FIFO will continue to
be loaded until it is full. Refer to Table 11.
5-4
FCR[5]
(MSB),
FCR[4]
(LSB)
TX trigger.
These bits are used to set the trigger level for the transmit FIFO
interrupt. The SC16C654/654D will issue a transmit empty interrupt
when the number of characters in FIFO drops below the selected trigger
level. Refer to Table 12.
3
FCR[3]
DMA mode select.
Logic 0 = Set DMA mode ‘0’ (normal default condition).
Logic 1 = Set DMA mode ‘1’
Transmit operation in mode ‘0’: When the SC16C654/654D is in the
16C450 mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode
(FIFOs enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there are
no characters in the transmit FIFO or transmit holding register, the
TXRDY pin will be a logic 0. Once active, the TXRDY pin will go to a
logic 1 after the rst character is loaded into the transmit holding
register.
Receive operation in mode ‘0’: When the SC16C654/654D is in
mode ‘0’ (FCR[0] = logic 0), or in the FIFO mode (FCR[0] = logic 1;
FCR[3] = logic 0) and there is at least one character in the receive FIFO,
the RXRDY pin will be a logic 0. Once active, the RXRDY pin will go to a
logic 1 when there are no more characters in the receiver.
相關PDF資料
PDF描述
935270050151 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP64
935270051512 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68
935270053529 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQCC44
935270053512 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQCC44
935270053518 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQCC44
相關代理商/技術參數
參數描述
935270713557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP
935270792551 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270792557 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270793551 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
935270793557 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*