參數資料
型號: 935264535557
廠商: NXP SEMICONDUCTORS
元件分類: 通信及網絡
英文描述: SPECIALTY TELECOM CIRCUIT, PQFP208
封裝: SOT-316, MQFP-208
文件頁數: 3/23頁
文件大小: 194K
代理商: 935264535557
1999 Jul 01
11
Philips Semiconductors
Product specication
Single Chip DAVIC/DVB-RC Cable Modem
VES1848
2
INPUT - OUTPUT SIGNAL DESCRIPTION
SYMBOL
PIN NUMBER
TYPE
DESCRIPTION
US_clk_in
173
I
XTAL oscillator input pin. Typically a fifth overtone XTAL oscillator is
connected between the US_clk_in and US_clk_out pins.
US_clk_out
174
O
XTAL oscillator output pin. Typically a fifth overtone XTAL oscillator
is connected between the US_clk_in and US_clk_out pins.
OOB_clk_in
78
I
XTAL oscillator input pin. Typically a fifth overtone XTAL oscillator is
connected between the OOB_clk_in and OOB_clk_out pins.
OOB_clk_out
79
O
XTAL oscillator output pin. Typically a fifth overtone XTAL oscillator
is connected between the OOB_clk_in and OOB_clk_out pins.
OOB_dig[6:0]
86,87,88,89
90,91,92
I
IF digital OOB signal. OOB_dig[6:0] is connected to an external A/D
converter. OOB_dig[6] is the MSB. When not used, OOB_dig[6 :0]
must be tied to ground.
OOB_saclk
85
O
(5V)
IF OOB Sampling ClocK. Can be used as the sampling clock of an
external 7-bit ADC that will generate OOB_dig signals.
Doob
54
O
(5V)
Output of the OOB DQPSK demodulator. Data are output on the
falling edge of clk_oob.
clk_oob
55
O
(5V)
Bit clock associated with Doob.
VAGC
82
O
(5V)
PWM encoded output signal for AGC. This signal is typically fed to
the AGC amplifier through a single RC network.
PWM2
81
O
(5V)
PWM encoded programmable signal. The encoded data is the
parameter PWM2 (C2[7-0]). This signal can be used to control a
second input of the AGC amplifier through a single RC network.
IBsymbclk
38
I
IB symbol clock. This clock is provided by the QAM demodulator.
Its polarity can be selected with parameter PsymbIB(AE.3).
IBclk
39
I
IB byte clock associated with the data bus IB[7:0].
Its polarity can be selected with parameter PbyteIB(AE.2).
IB[7:0]
41,42,45,46
47,48,49,50
I
IB MPEG2-TS input. These 8-bit parallel data are the outputs of the
DS QAM FEC.
When the parallel interface is selected (Parameter serie = 0,
address 82.6) then IB[7:0] is the transport stream input (IB[7] is the
MSB).
When the serial interface is selected (Parameter serie = 1, address
82.6) then the serial input is on pin IB[0] (pin 41).
PSYNC
40
I
If parameter Ps_DE=0 (address 83.7) : Pulse SYNChro. This input
signal must be high when the sync byte (4716) is provided on IB[7:0],
then it must be low until the next sync byte. If the serial interface is
selected, then PSYNC is high only during the first bit of the sync
byte (4716).
If parameter Ps_DE=1 (address 83.7) : data enable. This input
signal must be high during the first 188 bytes of the MPEG2-TS
packet. It is then low during the redondancy bytes.
EXT_SYNC
93
I
EXTernal SYNChro. Only used when parameter InExt=1 (88.1).
When not used, must be tied to ground.
This input signal toggles at each US burst start.
EXT_SYNC must be initiated to 0.
Fconti
94
O
(5V)
Programmable clock with the parameter contiCk (AF.[5-4]). This
clock must be used in continuous mode to generate Iconti[2:0] and
Qconti[2:0].
Iconti[2:0]
98,99,100
I
I input for the US modulator in continuous mode (parameter
contiMode=1 (AF.3), and contiMem=0 (AF.6)). This data bus is
clocked on the rising edge of Fconti clock.
相關PDF資料
PDF描述
08-3518-10 8 PIN SOLDER TAIL DIP SOCKET
06-3518-11 DIP16, IC SOCKET
08-3518-10TL DIP18, IC SOCKET
06-3518-10 DIP16, IC SOCKET
06-3518-10E DIP16, IC SOCKET
相關代理商/技術參數
參數描述
935267356112 制造商:NXP Semiconductors 功能描述:IC TEA1507PN
935268081112 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935268721125 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R
935269304128 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP
935269544557 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-2US1-V1.3