- 您現在的位置：買賣IC網 > PDF目錄24795 > 935242410118 (NXP SEMICONDUCTORS) LVC/LCX/Z SERIES, HEX 1-INPUT INVERT GATE, PDSO14 PDF資料下載
參數資料
| 型號： | 935242410118 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 門電路 |
| 英文描述： | LVC/LCX/Z SERIES, HEX 1-INPUT INVERT GATE, PDSO14 |
| 封裝： | 5.30 MM, PLASTIC, MO-150, SOT-337-1, SSOP-14 |
| 文件頁數： | 6/23頁 |
| 文件大?。?/td> | 163K |
| 代理商： | 935242410118 |
2003 Feb 24
14
Philips Semiconductors
Product specication
Hex inverter
74LVC04A
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is
recommended.
Reow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 250
°C. The top-surface temperature of the
packages should preferably be kept:
below 220 °C for all the BGA packages and packages
with a thickness
≥ 2.5mm and packages with a
thickness <2.5 mm and a volume
≥350 mm3 so called
thick/large packages
below 235 °C for packages with a thickness <2.5 mm
and a volume <350 mm3 so called small/thin packages.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45
° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°C.
相關PDF資料 |
PDF描述 |
|---|---|
| 935242400118 | LVC/LCX/Z SERIES, HEX 1-INPUT INVERT GATE, PDSO14 |
| 07.312.5053.0 | APC 1-2 5 |
| 07.312.5053.6 | APC 1-2 5 BLUE |
| 07.312.5053.7 | APC 1-2 5 GREEN |
| 07.312.5153.0 | TWC 1-2 5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935245650125 | 制造商:NXP Semiconductors 功能描述:Inverter 1-Element CMOS 5-Pin TSSOP T/R |
| 935248-90 | 制造商:JANCO 功能描述:935248-90 |
| 9-3525-012 | 制造商:KEYSTONE 功能描述:MODIFIED 3525,VERSION E |
| 935252-5 | 制造商:C-H 功能描述:935252-5 |
| 935257650112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY ICSUBS TO 935257650112 |
發布緊急采購，3分鐘左右您將得到回復。