- 您現在的位置：買賣IC網 > PDF目錄24624 > 9250CF-10LF (INTEGRATED DEVICE TECHNOLOGY INC) 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 PDF資料下載
參數資料
| 型號： | 9250CF-10LF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封裝： | 0.300 INCH, GREEN, SSOP-56 |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 452K |
| 代理商： | 9250CF-10LF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁
5
ICS9250- 10
1.
The ICS clock generator is a slave/receiver, I2C component. It can read back the data stored in the latches for verification.
Read-BackwillsupportIntelPIIX4"Block-Read"protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I2C interface, the protocol is set to use only "Block-Writes" from the controller. The
bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte
has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those
two bytes. The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
General I
2C serial interface information
The information in this section assumes familiarity with I2C programming.
For more information, contact ICS for an I2C programming application note.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D2
(H)
ICS clock will acknowledge
Controller (host) sends a dummy command code
Controller (host) sends a dummy byte count
ICS clock will acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 5
ICS clock will acknowledge each byte one at a time.
Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit.
Controler (host) sends the read address D3
(H)
ICS clock will acknowledge
ICS clock will send the byte count
Controller (host) acknowledges
ICS clock sends first byte (Byte 0) through byte 5
Controller (host) will need to acknowledge each byte
Controller (host) will send a stop bit
Notes:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D3(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Read:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D2(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Write:
相關PDF資料 |
PDF描述 |
|---|---|
| 925387-1 | WIRE TERMINAL |
| 925387-2 | TAB TERMINAL |
| 925552-8 | 1 mm2, STEEL, NICKEL FINISH, WIRE TERMINAL |
| 925553-1 | 2.5 mm2, BRASS, WIRE TERMINAL |
| 925553-8 | 2.5 mm2, BRASS, TIN FINISH, WIRE TERMINAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 9250CF-10LFT | 功能描述:時鐘發生器及支持產品 RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| 9250YF-27LF-T | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Frequency Generator and Integrated Buffers for Celeron & PII/IIITM |
| 9251 | 制造商:Apex Tool Group 功能描述:LOWER BRACKET FOR 9290 SERIES PNEUMATIC CUTTER |
| 9-251 | 制造商:Bernstein 功能描述:Bulk 制造商:BERNSTEIN WERKZEUGFABRIK 功能描述:VICE BALL SWIVEL MOUNTED 制造商:BERNSTEIN WERKZEUGFABRIK 功能描述:VICE, BALL SWIVEL MOUNTED 制造商:BERNSTEIN WERKZEUGFABRIK 功能描述:VICE, BALL SWIVEL MOUNTED; Accessory Type:Clamp Mounting Ball Joint Base; For Use With:Work Benches with Maximum Table Thickness of 80mm; SVHC:No SVHC (19-Dec-2012); Weight:950g ;RoHS Compliant: NA |
| 9251 0101000 | 功能描述:同軸電纜 13AWG 1C SHIELD 1000ft SPOOL BLACK RoHS:否 制造商:Murata RG 類型: 阻抗:50 Ohms 線規 - 美國線規（AWG）: 導體材料: 絞合: 長度:300 mm 外殼材料: 外徑: 屏蔽: |
發布緊急采購，3分鐘左右您將得到回復。