- 您現在的位置：買賣IC網 > PDF目錄24623 > 9248DF-39 (INTEGRATED DEVICE TECHNOLOGY INC) 150 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 PDF資料下載
參數資料
| 型號： | 9248DF-39 |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 150 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 封裝： | 0.300 INCH, SSOP-48 |
| 文件頁數： | 6/18頁 |
| 文件大?。?/td> | 321K |
| 代理商： | 9248DF-39 |
14
ICS9248-39
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS9248-
39 serve as dual signal functions to the device. During initial
power-up, they act as input pins. The logic level (voltage)
that is present on these pins at this time is read and stored
into a 5-bit internal data latch. At the end of Power-On reset,
(see AC characteristics for timing values), the device changes
the mode of operations for these pins to an output function.
In this mode the pins produce the specified buffered clocks
to external loads.
To program (load) the internal configuration register for these
pins, a resistor is connected to either the VDD (logic 1) power
supply or the GND (logic 0) voltage potential. A 10 Kilohm
(10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function when
a switch or 2 pin header is used. With no jumper is installed
the pin will be pulled high. With the jumper in place the pin
will be pulled low. If programmability is not necessary, than
only a single resistor is necessary. The programming resistors
should be located close to the series termination resistor to
minimize the current loop area. It is more important to locate
the series termination resistor close to the driver than the
programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| 9248DF-39LFT | 150 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 051-911-9072 | RF Coaxial Connectors |
| 9248YF-112-T | PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 9248YF-185LFT | 133.33 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO28 |
| 9248YF-195LF-T | 140 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 9248DF-39LF | 功能描述:時鐘發生器及支持產品 RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| 9248DF-39LFT | 功能描述:時鐘發生器及支持產品 RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| 9248EGM | 制造商:Excelta Corporation 功能描述:5" TAPER RLVD CUTTER WITH MELDED TEAL GRIPS |
| 9248YF-50-T | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Timing Generator for Pentium II Systems |
| 9249 | 制造商:Apex Tool Group 功能描述:PUSH ROD FOR 9290 SERIES PNEUMATIC CUTTER |
發布緊急采購，3分鐘左右您將得到回復。