參數資料
型號: 8P128SEA0301C15
廠商: WHITE ELECTRONIC DESIGNS CORP
元件分類: SRAM
英文描述: 8K X 8 MULTI DEVICE SRAM CARD, 150 ns, UUC68
封裝: CARD-68
文件頁數: 7/11頁
文件大?。?/td> 316K
代理商: 8P128SEA0301C15
5
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
SEA01-SEA04
February 2007
Rev. 4
FUNCTIONAL TRUTH TABLE
READ function
Common Memory
Attribute Memory
Function Mode
CE2# CE1# OE# WE#
REG#
D15-D8
D7-D0
REG#
D15-D8
D7-D0
Standby Mode
X
H
X
High-Z
X
High-Z
Byte Access (8 bits)
X
L
H
High-Z
Data Out
L
High-Z
Data Out
WRITE function
Standby Mode
X
H
X
Byte Access (8 bits)
X
L
H
L
H
X
Data In
L
X
Data In
CARD SIGNAL DESCRIPTION
Symbol
Type
Name and Function
A0 - A25
INPUT
ADDRESS INPUTS: A0 through A25 enable direct addressing of up to 64MB of memory on the card. Signal A0 is not
used in word access mode. A25 is the most signicant bit. (address pins used are based on card density,see pinout
for highest used address pin)
DQ0 – DQ7
DQ8 – DQ15
INPUT/OUTPUT
DATA INPUT/OUTPUT: DQ0 THROUGH DQ15 constitute the bi-directional databus. DQ0 - DQ7 constitute the lower
(even) byte and DQ8 - DQ15 the upper (odd) byte. Upper byte is Not Connected on this card.
CE1#, CE2#
INPUT
CARD ENABLE 1 AND 2: CE1# enables even byte accesses, CE2# control signal in PCMCIA standard, to access
high byte, - not used on this card
OE#
INPUT
OUTPUT ENABLE: Active low signal enabling read data from the memory card.
WE#
INPUT
WRITE ENABLE: Active low signal gating write data to the memory card.
RDY/BSY #
OUTPUT
READY/BUSY OUTPUT: Not used for SRAM cards
CD1#, CD2#
OUTPUT
CARD DETECT 1 and 2: Provide card insertion detection. These signals are connected to ground internally on the
memory card. The host socket interface circuitry shall supply 10K-ohm or larger pull-up resistors on these signal pins.
WP
OUTPUT
WRITE PROTECT: Follows hardware Write Protect Switch. When Switch is placed in on position, signal is pulled high
(10K ohm). When switch is off signal is pulled low.
VPP1, VPP2
N.C.
PROGRAM/ERASE POWER SUPPLY: Not used for SRAM cards.
VCC
CARD POW ER SUPPLY: 5.0V for all internal circuitry.
GND
GROUND: for all internal circuitry.
REG #
INPUT
ATTRIBUTE MEMORY SELECT: only used with cards built with optional attribute memory.
RST
INPUT
RESET: Not used for SRAM cards
WAIT #
OUTPUT
WAIT: This signal is pulled high internally for compatibility. No wait states are generated.
BVD1, BVD2
OUTPUT
BATTERY VOLTAGE DETECT: Provides status of Battery voltage.
BVD2 = BVD1 = VOH (battery voltage is guaranteed to retain data)
BVD2 = VOL, BVD1 = VOH (data is valid, battery recharge required)
BVD2 = BVD1 = VOL (data may no longer be valid, battery requires extended recharge)
VS1, VS2
OUTPUT
VOLTAGE SENSE: Noties the host socket of the card’s VCC requirements. VS1 and VS2 are open to indicate a 5V,
16 bit card has been inserted.
RFU
RESERVED FOR FUTURE USE
N.C.
NO INTERNAL CONNECTION TO CARD: pin may be driven or left oating
相關PDF資料
PDF描述
8P0043201C15 2M X 16 MULTI DEVICE SRAM CARD, 150 ns, UUC
8P0083101I25 4M X 16 MULTI DEVICE SRAM CARD, 150 ns, UUC
8P0163100C25 8M X 16 MULTI DEVICE SRAM CARD, 150 ns, UUC
8P512SRV1203C25 32M X 16 MULTI DEVICE SRAM CARD, 250 ns, XMA68
8P512SRV1301C15 32M X 16 MULTI DEVICE SRAM CARD, 150 ns, XMA68
相關代理商/技術參數
參數描述
8P15-E001 功能描述:D-Sub標準連接器 8P15-E001 15/DSUB/PL/EMI/AU-FL RoHS:否 制造商:Omron Electronics 位置/觸點數量:9 排數:2 型式:Female 安裝風格:Through Hole 安裝角:Right 端接類型:Solder 過濾:
8P15-E002 功能描述:D-Sub標準連接器 15/DSUB/PL/EMI/30 RoHS:否 制造商:Omron Electronics 位置/觸點數量:9 排數:2 型式:Female 安裝風格:Through Hole 安裝角:Right 端接類型:Solder 過濾:
8P15-N001 功能描述:D-Sub標準連接器 15P MALE DSUB GOLD SOLDER CUP RoHS:否 制造商:Omron Electronics 位置/觸點數量:9 排數:2 型式:Female 安裝風格:Through Hole 安裝角:Right 端接類型:Solder 過濾:
8P15-N002 功能描述:D-Sub標準連接器 15/DSUB/PL/STD/30 RoHS:否 制造商:Omron Electronics 位置/觸點數量:9 排數:2 型式:Female 安裝風格:Through Hole 安裝角:Right 端接類型:Solder 過濾:
8P1P00217BAL421 功能描述:CONN PLUG MALE 2POS SOLDER CUP 制造商:norcomp inc. 系列:QUIK-LOQ? 8P1P 包裝:托盤 零件狀態:在售 連接器類型:插頭,公引腳 針腳數:2 外殼尺寸 - 插件:- 外殼尺寸,MIL:- 安裝類型:自由懸掛 端接:焊杯 緊固類型:推挽式 朝向:帶標記 侵入防護:IP50 - 防塵 外殼材料,鍍層:聚丙烯腈丁二烯苯乙烯(ABS),聚碳酸酯(PC) 觸頭鍍層:金 特性:后殼,應力消除 電壓 - 額定:500V 額定電流:10A 觸頭鍍層厚度:7μin(0.18μm) 工作溫度:-20°C ~ 120°C 標準包裝:18