- 您現在的位置：買賣IC網 > PDF目錄7077 > 8344 (3M)WORKSURFACE RIGID ESD DISSP GRAY PDF資料下載
參數資料
| 型號： | 8344 |
| 廠商： | 3M |
| 文件頁數： | 7/16頁 |
| 文件大小： | 0K |
| 描述： | WORKSURFACE RIGID ESD DISSP GRAY |
| 標準包裝： | 1 |
| 系列： | 8300 |
| 墊子類型： | 桌子，工作臺 |
| 形狀： | 矩形 |
| 長度： | 3'（0.91m） |
| 寬： | 2'（0.61m） |
| 厚度： | 0.13"（3.30mm） |
| 顏色： | 灰 |
| 材質： | Laminate |
| 特點： | 耗散 |
| 包括： | 接地軟線，接地卡扣 |
| 其它名稱： | 05400718619 98079815852 |
1
78-8136-3801-8
2.0
Cleaning and Maintenance
A.
The 3M Rigid Worksurface 8300 Series is readily cleaned with 3M Static Control Worksurface
Mark Remover 8001. It can also be cleaned with warm water and mild detergents. Many commercially
available detergents are suitable, including common household dishwashing liquids.
B.
Nonabrasive, commercially available surface cleaners such as glass cleaners or products similar to
SoftScrub are suitable. Cleaners containing abrasives or strong acids or alkalines should be avoided.
C.
Stains such as those caused by solder flux, varnishes, ink, etc., can be removed with organic solvents
(alcohols, ketones, xylene, mineral spirits). Such stains can also be removed by a twominute exposure
to a 5% hypochlorite bleach (common laundry bleach) followed immediately by a clean water rinse.
D.
The surface should be protected from heat and from cuts and gouges by means of a hot pad and/or
cutting board. 3M Rigid Worksurfaces will not be affected by drops of molten solder, but will blister
if a soldering iron or some other intensely hot object is left on the surface. Blistering will occur at
approximately 400°F (204°C).
E.
ANYTIME THE LAMINATE SURFACE IS CLEANED OR OTHERWISE AFFECTED, THE
ELECTRICAL PERFORMANCE SHOULD BE VERIFIED.
3.0
Repair
A.
Colored paste can be used to visually repair minor defects in the top surface.
B.
Laminate that was adhered with contact adhesive and that lifts from the substrate can be readhered by
applying heat and pressure. A simple method is to place a piece of cloth over the problem area and then
iron it with a household iron.
C.
While most decorative commercial laminate can be recovered with additional laminate by sanding the
existing surface, cleaning it, and reapplying adhesive, this practice will not work well with 3M Static
Dissipative Rigid Worksurface 8300 Series. The 3M laminate is manufactured with a special, tough,
abrasionresistant coating that resists sanding. Therefore, adhesive will not bond well to the surface.
4.0
Troubleshooting Guide
Surface changes
Discoloration
Due to sunlight
Laminate not intended for outdoor use
Keep laminate away from direct
sunlight
Due to chemicals
Avoid prolonged exposure to bleaches,
acids, alkalis
Due to heat
Remove/insulate heat source
Dents/depressions due to substrate
imperfections
Use higherdensity, thicker, or
smoother substrate
Cover at least 80% of the bond
surfaces with adhesive
相關PDF資料 |
PDF描述 |
|---|---|
| 8343 | WORKSURFACE RIGID ESD DISSP BGE |
| 2-1419104-2 | RELAY GEN PURPOSE SPST 30A 48V |
| 431301-23-0 | TERM BARRIER 23CIRC 1 ROW .4375 |
| V23061B1005A301 | RELAY GEN PURPOSE SPDT 8A 12V |
| GP1500R-0.010-02-0816 | THERMAL PAD .010" 8"X16" GP1500R |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 83440 00000020 05 | 功能描述:工業壓力 / 力傳感器 PRESSURE SWITCH RoHS:否 制造商:Honeywell 工作壓力:0 bar to 25 bar 壓力類型:Sealed Gauge 準確性:0.25 % 輸出類型: 安裝風格:Screw 工作電源電壓:8 V to 30 V 輸出電壓:8 V to 30 V 封裝: |
| 83440-00000020-05 | 功能描述:板上安裝壓力/力傳感器 PRESSURE SWITCH RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| 834402 | 制造商:Whirlpool 功能描述:KNOB, SURFACE *NLA 08/06* |
| 8-34404-2 | 制造商:TE Connectivity 功能描述:TERMINAL,BUDG R 12-10 8 - Bulk |
| 834-40CM-9.5 | 制造商:NORTH SAFETY PRODUCTS 功能描述:GLOVE GAUNTLET CHEM RES 40CM (1PR) |
發布緊急采購，3分鐘左右您將得到回復。