- 您現在的位置：買賣IC網 > PDF目錄7077 > 8343 (3M)WORKSURFACE RIGID ESD DISSP BGE PDF資料下載
參數資料
| 型號： | 8343 |
| 廠商： | 3M |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | WORKSURFACE RIGID ESD DISSP BGE |
| 標準包裝： | 1 |
| 系列： | 8300 |
| 墊子類型： | 桌子，工作臺 |
| 形狀： | 矩形 |
| 長度： | 3'（0.91m） |
| 寬： | 2'（0.61m） |
| 厚度： | 0.13"（3.30mm） |
| 顏色： | 淺褐 |
| 材質： | Laminate |
| 特點： | 耗散 |
| 包括： | 接地軟線，接地卡扣 |
| 其它名稱： | 05400718618 98079815845 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
3
78-8136-3801-8
3M Static Dissipative Rigid Worksurface 8300 Series
Installation Instructions
1.0
Industry definitions
A.
Backer: a phenolic sheet placed on the opposite (back) side of the substrate to which the laminate is
adhered. The backer is used to offset stresses on the substrate caused by the laminate. It also acts as a
moisture barrier (See Section 10.0).
B.
No drip edge: a raised rim on a counter/benchtop/work surface to prevent runoff.
C.
Glue line: the adhesive layer used to adhere laminate to the surface of a substrate.
D.
Jroller 3 inch: a handheld roller used to apply even pressure when bonding laminate to a surface. A
pressure of 50 pounds per lineal inch is recommended for most contact adhesives.
E.
NEMA: National Electrical Manufacturers’ Association
F.
NEMA LD 32000: HighPressure Decorative Laminate
NEMA LD 32000 Annex A: Performance, Applications, Fabrication, & Installation of HighPressure
Decorative Laminate
G.
Off Fall: excess laminate due to dimensional inconsistencies or irregularities in the substrate to which
the laminate is applied.
H.
Postforming: bending laminate sheet over or around the edge profile of a counter; this requires special
procedures (See Section 8.0)
I.
Tempilaq/Templistik: colored marking chalk or wax that is heatsensitive, i.e., changes color or melts
when a certain temperature is reached; used to indicate that the surface of a laminate has reached the
proper temperature for thermoforming (325°F). (See Section 8.0)
J.
Waterfall edge: a 90° postformed edge on a counter.
2.0
3M Static Dissipative Rigid Worksurface 8300 Series Specifications
A.
Resistance values: Resistance measurements are used to establish the chargedraining capability of the
static dissipative rigid worksurface. The ESD Association evaluates two resistance values in classifying
dissipative laminate and other static control surfacing materials. The tests are as follows:
1) Surface to Ground point resistance Use a 3M Test Kit 701 for static control surfaces. Test the
resistance between the top surface of the table top and the ground point per ESD Association
Standard 4.1 [tested at 72°F (22°C), 50% RH]. The values should be between 1 x 106 1 x 109 ohms
(l 1,000 Megohms).
2) Point to Point resistance Use a 3M Test Kit 701 for static control surfaces. Test the resistance
between two points on the top surface of the table top per ESD Association Standard 4.1 [Tested at
72°F (22°C), 50% RH]. Typical value is 6 x 107 ohms (60 Megohms).
AdditionalTest:
Ground Point to Ground Point resistance – Perform this test when the worksurface ground connection
is to be electrically monitored. Equipment such as the 3M Workstation Monitor 724 continuously
monitors the ground connection through the interior conductive layer of the laminate. Use a 3M Test
Kit 701 for static control surfaces to pretest and ensure that the grounding hardware is making sufficient
contact to the conductive layer. Connect one of the test leads to each of the two ground hardware items
installed on the tabletop. Set the test selector switch to the 10V position. Push the test button and the
reading should be less than 1 x 106 ohms (1 Megohm).
B.
Thickness: 0.040 in. nominal
C.
Density: 1.45 grams/cc
相關PDF資料 |
PDF描述 |
|---|---|
| 2-1419104-2 | RELAY GEN PURPOSE SPST 30A 48V |
| 431301-23-0 | TERM BARRIER 23CIRC 1 ROW .4375 |
| V23061B1005A301 | RELAY GEN PURPOSE SPDT 8A 12V |
| GP1500R-0.010-02-0816 | THERMAL PAD .010" 8"X16" GP1500R |
| 431201-23-0 | TERM BARRIER 23CIRC 1 ROW .4375 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8-34304-1 | 功能描述:端子 SPLICE CE 22-14 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
| 8-34306-1 | 制造商:TE Connectivity 功能描述:SPLICES TERM 16-22AWG 19.05MM TIN - Bulk |
| 8-34308-2 | 制造商:TE Connectivity 功能描述:SPLICES TERM 10-22AWG 24.77MM TIN - Bulk |
| 83431032A35 | 制造商:n/a 功能描述:Ships in 2 days |
| 8-34313-1 | 功能描述:端子 PIDG HK 22-16 COM 22-18 MIL 6 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
發布緊急采購，3分鐘左右您將得到回復。