- 您現在的位置：買賣IC網 > PDF目錄376466 > 80-0211-C (Electronic Theatre Controls, Inc.) Speech And Music Processor PDF資料下載
參數資料
| 型號： | 80-0211-C |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Speech And Music Processor |
| 中文描述： | 語音和音樂處理器 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 358K |
| 代理商： | 80-0211-C |
SC-691
Data sheet
Read Operation By The Master
6
P/N 80-0211-C
2003 Sensory Inc.
The process for the read operation by the master is the same in either 4-bit or 8-bit mode. The read operation by
the master happens when the slave wants to send something to the master. The read process is initiated by the
slave by pulling OUTRDY_ low when it is ready.
The following events take place during the read operation:
The SC-691 puts the data to be sent to the master on the internal bus.
The SC-691 sets OUTRDY_ low to indicate that it is ready to send data to the microcontroller.
The microcontroller sets R/W_ high to indicate a read operation.
The microcontroller sets STROBE_ low. The data is available on the external data-bus at this point.
The microcontroller reads the data from the bus.
The microcontroller sets STROBE_ high. The SC-691 also pulls OUTRDY_ high at the rising edge of
STROBE_.
The data is taken from the external data-bus after STROBE_ goes high.
The microcontroller should latch or read in the data while STROBE is low. When the microcontroller sets
STROBE_ high, the SC-691 sets OUTRDY_ high to indicate that the data has been successfully transferred.
A) Sequence of events for a single read operation:
OUTRDY
STROBE
DATA
COMMAND/DATA
R/W
B) Read-Two speech data transfer sequences:
OUTRDY
STROBE
DATA
COMMAND/DATA
R/W
Figure 3:
Data Transfer – Read
Write Operation By The Master
The process for the write operation by the master is the same in either 4-bit or 8-bit mode. The write operation
by the master happens when the slave is ready to request data or command from the master. The write process
is initiated by the slave by pulling INRDY_ low when the slave is ready to receive data. The following events
take place during the write operation:
The SC-691 sets INRDY_ low to indicate that it is ready to receive data from the microcontroller.
The microcontroller sets R/W _low to indicate a write operation.
The microcontroller puts the data in the external data-bus.
The microcontroller sets STROBE_ low after the data is valid.
The microcontroller sets STROBE_ high after a minimum of 300 ns. The SC-691 also pulls INRDY_ high at
the rising edge of STROBE_.
The data is latched in the SC-691 at the rising edge of STROBE_.
相關PDF資料 |
PDF描述 |
|---|---|
| 80-0213-B | SPEECH AND MUSIC PROCESSORS |
| 80-0274-E | VR Stamp⑩ With Serial EEPROM Speech Recognition Module |
| 80-0276-F | System Level ESD Mitigation |
| 80-0281-E | VR STAMP WITH SERIAL EEPROM |
| 800D-5 | THERMOPILE TYPE INFRARED SENSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 800212 | 制造商:Schaffner 功能描述:Power Line Filter 0Hz to 400Hz 6.5A 250VAC Faston Flange Mount |
| 8002-12-00 | 功能描述:簧片繼電器 REED RELAY MAG HI-RF 3.3V SMD RoHS:否 制造商:MEDER electronic (Standex) 觸點形式:1 Form A (SPST-NO) 線圈電壓:5 VDC 最大開關功率:100 W 最大開關電流:1 A 線圈抑制二極管:No 線圈電阻:220 Ohms 端接類型: |
| 8002-12-001 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| 8002-12-01 | 功能描述:簧片繼電器 REED RELAY SPDT 12V RoHS:否 制造商:MEDER electronic (Standex) 觸點形式:1 Form A (SPST-NO) 線圈電壓:5 VDC 最大開關功率:100 W 最大開關電流:1 A 線圈抑制二極管:No 線圈電阻:220 Ohms 端接類型: |
| 8002-12-011 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。