- 您現在的位置：買賣IC網 > PDF目錄360549 > 7P064 IDE 1511C25 2.5 Flash IDE Drives(2.5閃速存儲器IDE器件（64MB）) PDF資料下載
參數資料
| 型號： | 7P064 IDE 1511C25 |
| 英文描述： | 2.5 Flash IDE Drives(2.5閃速存儲器IDE器件（64MB）) |
| 中文描述： | 2.5閃存IDE驅動器（2.5閃速存儲器的IDE器件（64MB以上）） |
| 文件頁數： | 5/10頁 |
| 文件大小： | 70K |
| 代理商： | 7P064 IDE 1511C25 |
7PxxxIDE15xxC25
September 2000 Rev. 0 – ECO #13224
5
White Electronic Designs Corporation
(508) 366-5151
Drive Pin Explanation
Address bus (A0 to A2: input):
In True IDE Mode only A [2 : 0] are used for selecting the one of eight
registers in the Task File.
Data bus (D0 to D15: input/output):
Data bus is D0 to D15. D0 is the LSB of the Even Byte of the
Word. D8 is the LSB of the Odd Byte of the Word.
Card enable (-CE1, -CE2: input):
In True IDE Mode -CE2 is used for select the Alternate Status
Register and the Device Control Register while -CE1 is the chip select for the other task file registers.
I/O read (-IORD: input):
-IORD is used for control of read data in the Task File area.
I/O write (-IOWR: input):
-IOWR is used for control of data write in the Task File area.
Interrupt request (IRQ: output):
In True IDE Mode the signal is the active high Interrupt Request to the
host.
-IOIS16: (output)
In True IDE Mode this output signal is asserted low when this device is expecting a
word data transfer cycle.
Disk active/slave present (-DASP: input/output):
In True IDE Mode -DASP is the Disk Active/Slave
Present signal in the Master/Slave handshake protocol.
Reset (-RESET: input):
By assertion of the RESET signal, all registers of this card are cleared and the
RDY/-BSY signal turns to high level. In True IDE Mode -RESET is the active low hardware reset from
the host.
Wait (-WAIT, IORDY: output):
. In True IDE Mode this output signal may be used as IORDY. As for
this controller, this output is high impedance state constantly.
Pass diagnostic (-PDIAG: input/output):
. In True IDE Mode, -PDIAG is the Pass Diagnostic signal in
the Master/Slave handshake protocol.
Card select (-CSEL: input):
This internally pulled up signal is used to configure this device as a Master
or a Slave when configured in the True IDE Mode. When this pin is grounded, this device is configured as
a Master. When the pin is open, this device is configured as a Slave.
Master/Slave configuration:
The drive can be installed as a Primary or Secondary drive, as either a
Master or a Slave. If the flash drive is being installed as a Slave, pin 48 or pin 49 must be grounded. Pins
48 and 49 are inputs with pull up resistors. If both pins are open, the flash drive is configured as the Master
drive.
相關PDF資料 |
PDF描述 |
|---|---|
| 7P192ATA2500C25 | Flash Memory Card(192M位閃速存儲器卡) |
| 7P800ATA2514C25 | Flash Memory Card(800M位閃速存儲器卡) |
| 7P224ATA2500C25 | Flash Memory Card(224M位閃速存儲器卡) |
| 7P320ATA2500C25 | Flash Memory Card(320M位閃速存儲器卡) |
| 7P448ATA2500C25 | Flash Memory Card(448M位閃速存儲器卡) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 7P-10.000MBP-T | 功能描述:OSC TCXO 10.000MHZ CMOS SMD 制造商:txc corporation 系列:* 零件狀態:在售 標準包裝:1,000 |
| 7P102V330A052 | 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum |
| 7P102V330N042 | 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum |
| 7P102V360A052 | 功能描述:鋁質電解電容器-管理單元 1000uF 360V PHOTO RoHS:否 制造商:Nichicon 電容:470 uF 容差:20 % 電壓額定值:450 V ESR: 工作溫度范圍:- 25 C to + 105 C 系列:AR 直徑:35 mm 長度:45 mm 引線間隔:10 mm 產品:General Purpose Electrolytic Capacitors |
| 7P122V330A052 | 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum |
發布緊急采購，3分鐘左右您將得到回復。