- 您現在的位置：買賣IC網 > PDF目錄369357 > 7B991RPFI (MAXWELL TECHNOLOGIES) Programmable Skew Clock Buffer (PSCB) PDF資料下載
參數資料
| 型號： | 7B991RPFI |
| 廠商： | MAXWELL TECHNOLOGIES |
| 元件分類： | 時鐘及定時 |
| 英文描述： | Programmable Skew Clock Buffer (PSCB) |
| 中文描述： | PLL BASED CLOCK DRIVER, 8 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), DFP32 |
| 封裝： | RAD PAK, DFP-16 |
| 文件頁數： | 11/17頁 |
| 文件大小： | 253K |
| 代理商： | 7B991RPFI |
M
11
All data sheets are subject to change without notice
2002 Maxwell Technologies.
All rights reserved.
Programmable Skew Clock Buffer (PSCB)
7B991
09.23.02 Rev 4
O
PERATIONAL
M
ODE
D
ESCRIPTIONS
F
IGURE
5. Z
ERO
-S
KEW
AND
/
OR
Z
ERO
-D
ELAY
C
LOCK
D
RIVER
Figure 5 shows the PSCB configured as a zero-skew clock buffer. In this mode, the 7B991 can be used as the basis
for a low-skew clock distribution tree. When all of the function select inputs (xF0, xF1) are left open, the outputs are
aligned and may each drive a termnated transmssion line to an independent load. The FB input can be tied to any
output in this configuration and the operating frequency range is selected with the FS pin. The low-skew specification,
coupled with the ability to drive termnated transmssion lines (with impedances as low as 50
), allow efficient printed
circuit board design.
F
IGURE
6. P
ROGRAMMABLE
-S
KEW
C
LOCK
D
RIVE
Figure 6 shows a configuration to equalize skew between metal traces of different lengths. In addition to low skew
between outputs, the PSCB can be programmed to stagger the timng of its outputs. The four groups of output pairs
can each be programmed to different output timng. Skew timng can be adjusted over a wide range in small incre-
ments with the appropriate strapping of the function select pins. In this configuration, the 4Q0 output is fed back to FB
and configured for zero skew The other three pairs of outputs are programmed to yield different skews relative to the
feedback. By advancing the clock signal on the longer traces or retarding the clock signal on shorter traces, all loads
can receive the clock pulse at the same time.
In this illustration, the FB input is connected to an output with 0-ns skew (xF1, xF0 = MID) selected. The internal PLL
synchronizes the FB and REF inputs and aligns their rising edges to insure that all outputs have precise phase align-
ment.
相關PDF資料 |
PDF描述 |
|---|---|
| 7B991RPFS | Programmable Skew Clock Buffer (PSCB) |
| 7B991 | Programmable Skew Clock Buffer (PSCB) |
| 7BT2F9A-361 | HIGH CAPACITY ENVIRONMENTALLY SEALED |
| 7BT2 | HIGH CAPACITY ENVIRONMENTALLY SEALED |
| 7BT2F15A-361 | HIGH CAPACITY ENVIRONMENTALLY SEALED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 7B991RPFS | 制造商:MAXWELL 制造商全稱:Maxwell Technologies 功能描述:Programmable Skew Clock Buffer (PSCB) |
| 7B991V-2JC | 制造商:Cypress Semiconductor 功能描述: |
| 7B991V-5JZC | 制造商:Cypress Semiconductor 功能描述: |
| 7B991V-7JXC | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 7B991VT | 制造商:Cypress Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。