- 您現在的位置：買賣IC網 > PDF目錄10605 > 78P2351-IGT/F (Maxim Integrated Products)LINE INTERFACE UNIT 100-LQFP PDF資料下載
參數資料
| 型號： | 78P2351-IGT/F |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | LINE INTERFACE UNIT 100-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 90 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | E4，OC-3，STM1-E |
| 電源電壓： | 3.15 V ~ 3.45 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（16x16） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
78P2351
Single Channel
OC-3/ STM1-E/ E4 LIU
Page: 13 of 42
2006 Teridian Semiconductor Corporation
Rev. 2.4
REGISTER DESCRIPTION (continued)
PORT-SPECIFIC REGISTERS
For PA[3:0] = 1 only. Accessing a register with port address greater than 1 constitutes an invalid command.
ADDRESS 1-0: MODE CONTROL REGISTER
BIT
NAME
TYPE
DFLT
VALUE
DESCRIPTION
7
PDTX
R/W
0
Transmitter Power-Down:
0 : Normal Operation
1 : Power-Down. CMI Transmit output is tri-stated.
6
PDRX
R/W
0
Receiver Power-Down:
0 : Normal Operation
1 : Power-Down
5
PMODE
R/W
X
Parallel Mode Interface Selection:
When PAR=0, PMODE is invalid and defaults to logic ‘1’;
When PAR=1, (Master Control Register: bit 5), PMODE selects the
source of the transmit parallel clock, either taken from the framer
externally or generated internally. Default value is determined by
CKMODE pin setting upon power up or reset.
0: Slave Timing. PICK clock input to the transmitter
1: Master Timing. PTOCK clock output from the transmitter
4
SMOD[1]
R/W
X
3
SMOD[0]
R/W
X
Serial Mode Interface Selection:
When PAR=0 (Master Control Register: bit 5), SMOD[1:0] configures
the transmitter’s system interface.
Default values determined by
CKMODE pin setting upon power up or reset.
SMOD[1] SMOD[0]
0
Synchronous clock and data are passed through a
FIFO. The CDR is bypassed.
1
0
Synchronous data is passed through the CDR and
then through the FIFO.
0
1
Plesiochronous data is passed through the CDR to
recover a clock. FIFO is bypassed because the
data is not synchronous with the reference clock.
1
Loop Timing Mode Enable: The recovered receive
clock is used as the reference for the transmit DLL
and FIFO.
When PAR=1 (Master Control Register: bit 5), setting SMOD[1:0] = 11
will enable Loop Timing Mode.
Default values are determined by
CKMODE pin setting upon power up or reset as follows:
CKMODE Low
SMOD[1:0] default = 00 (no effect)
CKMODE Float
SMOD[1:0] default = 11 (loop-timing enable)
CKMODE High
SMOD[1:0] default = 01 (no effect)
2
MON
R/W
0
Receive Monitor Mode Enable:
0: Normal Operation
1: Adds 20dB of flat gain to the receive signal before equalization.
NOTE: Monitor mode is only available in CMI mode.
1:0
--
R/W
00
Reserved
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3098EAESE+ | IC RS485/422 RX 32MBPS 16-SOIC |
| RM12WBP-5P | CONN PLUG 5POS W/PIN INSERT |
| RM12WBP-4P | CONN PLUG 4POS W/PIN INSERT |
| MAX233AEPP+G36 | IC TXRX RS232 5V 20-DIP |
| VE-B74-MX-F3 | CONVERTER MOD DC/DC 48V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 78P2351-IGTR | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Single Channel OC-3/ STM1-E/ E4 LIU |
| 78P2351-IGTR/F | 功能描述:接口 - 專用 Single Ch OC-3/STM-1e/E4 LIU RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| 78P2351R | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter |
| 78P2351R-DB | 功能描述:界面開發工具 78P2351R Demo Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| 78P2351R-IM | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter |
發布緊急采購，3分鐘左右您將得到回復。