- 您現在的位置：買賣IC網 > PDF目錄360515 > 7510 7510 Group Datasheet Datasheet 469K/JAN.10.98 PDF資料下載
參數資料
| 型號： | 7510 |
| 英文描述： | 7510 Group Datasheet Datasheet 469K/JAN.10.98 |
| 中文描述： | 7510組數據表數據表469K/JAN.10.98 |
| 文件頁數： | 35/44頁 |
| 文件大小： | 469K |
| 代理商： | 7510 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
34
7510 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is “1”. Af-
ter a reset, initialize flags which affect program execution. In
particular, it is essential to initialize the index X mode (T) and the
decimal operation mode (D) flag because of their effect on calcu-
lations.
Interrupts
The contents of the interrupt request bits do not change immedi-
ately after they have been written.
After writing to an interrupt request register, execute at least one
instruction before performing a BBC or BBS instruction.
Decimal Calculations
To calculate in decimal notation, set the decimal operation mode
flag (D) to “1”, then execute the ADC or the SBC instruction. Only
the ADC and the SBC instruction yield proper decimal results. Af-
ter executing the ADC or SBC instruction, execute at least one
instruction before executing the SEC, the CLC, or the CLD instruc-
tion.
In decimal mode, the values of the negative (N), overflow (V), and
zero (Z) flag are invalid. The carry flag can be used to indicate
whether a carry or borrow has occurred.
Initialize the carry flag before each calculation. Clear the carry flag
before the ADC instruction and set the flag before the SBC in-
struction.
Timers
If a value n (between 0 and 255) is written to a timer latch, the fre-
quency division ratio is 1/(n+1).
Multiplication and Division Instructions
The index X mode (T) and the decimal mode (D) flag do not affect
the MUL and DIV instruction.
The execution of these instructions does not change the contents
of the processor status register.
Ports
The contents of the port direction registers cannot be read.
The following cannot be used:
G
the data transfer instruction (LDA, etc.)
G
the operation instruction when the index X mode flag (T) is “1”
G
the addressing mode which uses the value of a direction register
as an index
G
the bit-test instruction (BBC or BBS, etc.) to a direction register
G
the read-modify-write instruction (ROR, CLB, or SEB, etc.) to a
direction register
Use instructions such as LDM and STA, etc., to set the port direc-
tion registers.
Serial I/O
In clock synchronous serial I/O, if the receive side is using an ex-
ternal clock and it is to output the S
RDY
signal, set the transmit
enable bit, the receive enable bit, and the S
RDY
output enable bit
to “1”.
Serial I/O continues to output the final bit from the T
X
D pin after
transmission is completed.
Instruction Execution Time
The instruction execution time is obtained by multiplying the fre-
quency of the internal clock
φ
by the number of cycles needed to
execute an instruction.
The number of cycles required to execute an instruction is shown
in the list of machine instructions.
In high-speed mode, the frequency of the internal clock
φ
is half of
the X
IN
frequency.
In middle-speed mode, the frequency of the internal clock
φ
is one
eighth the X
IN
frequency.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM produc-
tion:
1. Mask ROM Order Confirmation Form
2. Mark Specification Form
3. Data to be written to ROM, in EPROM form (three identical
copies)
相關PDF資料 |
PDF描述 |
|---|---|
| 7513 | 7513 Group Datasheet Datasheet 1067K/FEB.06.01 |
| 75160-101-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-102-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-105-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
| 75160-301-36 | STIFTLEISTE ABTRENNBAR 1REIHIG 36POL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 75100 | 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:2.54mm (.100”) Pitch C-Grid Compliant Pin Headers |
| 75-100 | 制造商:THORDARSON MEISSNER 功能描述:Power Supply,Foreign,Portable,in:100/120/220/240V,50/60HZ,out:120V,100VA |
| 75-100/4068 | 制造商:Orbis 功能描述:VDE TOOLBAG 11-PCS. |
| 75-1000 | 制造商:THORDARSON MEISSNER 功能描述:Power Supply,Foreign,Portable,in:100/120/220/240V,50/60HZ,out:120V,1000VA 制造商:Datak Corporation 功能描述:Connector Accessories Single Gang Cover Designer Style Keystone Insert White |
| 751000 BK001 | 功能描述:HOOK-UP STRND 10AWG BLACK 1000' 制造商:alpha wire 系列:751000 零件狀態:有效 電纜類型:電子線 線規:10 AWG 導線股數:105/30 導體材料:銅，鍍錫 護套（絕緣）材料:聚乙烯（XLPE），輻照 護套（絕緣）直徑:0.180"（4.57mm） 護套（絕緣）厚度:0.031"（0.80mm） 長度:1000'（304.80m） 電壓:600V 工作溫度:-40°C ~ 125°C 套管顏色:黑 等級:UL 式 3173 特性:- 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。