- 您現在的位置：買賣IC網 > PDF目錄360426 > 74F169SCX Synchronous Up/Down Counter PDF資料下載
參數資料
| 型號： | 74F169SCX |
| 元件分類： | 通用總線功能 |
| 英文描述： | Synchronous Up/Down Counter |
| 中文描述： | 同步加/減計數器 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 94K |
| 代理商： | 74F169SCX |
3
www.fairchildsemi.com
7
Functional Description
The 74F161A and 74F163A count in modulo-16 binary
sequence. From state 15 (HHHH) they increment to state 0
(LLLL). The clock inputs of all flip-flops are driven in paral-
lel through a clock buffer. Thus all changes of the Q outputs
(except due to Master Reset of the 74F161A) occur as a
result of, and synchronous with, the LOW-to-HIGH transi-
tion of the CP input signal. The circuits have four funda-
mental modes of operation, in order of precedence:
asynchronous
reset (74F161A), synchronous
(74F163A), parallel load, count-up and hold. Five control
inputs
—
Master Reset (MR, 74F161A), Synchronous Reset
(SR, 74F163A), Parallel Enable (PE), Count Enable Paral-
lel (CEP) and Count Enable Trickle (CET)
—
determine the
mode of operation, as shown in the Mode Select Table. A
LOW signal on MR overrides all other inputs and asynchro-
nously forces all outputs LOW. A LOW signal on SR over-
rides counting and parallel loading and allows all outputs to
go LOW on the next rising edge of CP. A LOW signal on PE
overrides counting and allows information on the Parallel
Data (P
n
) inputs to be loaded into the flip-flops on the next
reset
rising edge of CP. With PE and MR ('F161A) or SR
(74F163A) HIGH, CEP and CET permit counting when
both are HIGH. Conversely, a LOW signal on either CEP or
CET inhibits counting.
The 74F161A and 74F163A use D-type edge triggered flip-
flops and changing the SR, PE, CEP and CET inputs when
the CP is in either state does not cause errors, provided
that the recommended setup and hold times, with respect
to the rising edge of CP, are observed.
The Terminal Count (TC) output is HIGH when CET is
HIGH and the counter is in state 15. To implement synchro-
nous multi-stage counters, the TC outputs can be used
with the CEP and CET inputs in two different ways. Please
refer to the 74F568 data sheet. The TC output is subject to
decoding spikes due to internal race conditions and is
therefore not recommended for use as a clock or asynchro-
nous reset for flip-flops, counters or registers.
Logic Equations: Count Enable
=
CEP
CET
PE
TC
=
Q
0
Q
1
Q
2
Q
3
CET
Mode Select Table
H
=
HIGH Voltage Level
L
=
LOW Voltage Level
X
=
Immaterial
Note 1:
For 74F163A only
State Diagram
Block Diagram
SR
(Note 1)
PE
CET
CE
P
Action on the Rising
Clock Edge (
Reset (Clear)
Load (P
n
→
Q
n
)
Count (Increment)
No Change (Hold)
No Change (Hold)
)
L
H
H
H
H
X
L
H
H
H
X
X
H
L
X
X
X
H
X
L
相關PDF資料 |
PDF描述 |
|---|---|
| 74F169SJX | Synchronous Up/Down Counter |
| 74F160ADC | Synchronous Up Counter |
| 74F161APCQR | Synchronous Up Counter |
| 74F161ASCQR | Synchronous Up Counter |
| 74F161ASCX | Synchronous Up Counter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 74F169SJ | 功能描述:計數器移位寄存器 4-State Sy Bidir Ctr RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
| 74F169SJ_Q | 功能描述:計數器 IC 4-State Sy Bidir Ctr RoHS:否 制造商:NXP Semiconductors 計數器類型:Binary Counters 邏輯系列:74LV 位數:10 計數法: 計數順序: 工作電源電壓:1 V to 5.5 V 工作溫度范圍:- 40 C to + 125 C 封裝 / 箱體:SOT-109 封裝:Reel |
| 74F169SJX | 功能描述:計數器移位寄存器 4-State Sy Bidir Ctr RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
| 74F173 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad D-type flip-flop 3-State |
| 74F174 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Hex D Flip-Flop with Master Reset |
發布緊急采購，3分鐘左右您將得到回復。