- 您現在的位置：買賣IC網 > PDF目錄360417 > 74ALVCH32501EC (NXP SEMICONDUCTORS) 36-bit universal bus transceiver with direction pin; 5 V tolerant; 3-state PDF資料下載
參數資料
| 型號： | 74ALVCH32501EC |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 通用總線功能 |
| 英文描述： | 36-bit universal bus transceiver with direction pin; 5 V tolerant; 3-state |
| 中文描述： | ALVC/VCX/A SERIES, DUAL 18-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PBGA114 |
| 封裝： | 16 X 5.50 MM, 1.05 MM HEIGHT, PLASTIC, SOT-537-1, LFBGA-114 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 88K |
| 代理商： | 74ALVCH32501EC |
2000 Mar 16
14
Philips Semiconductors
Product specification
36-bit universal bus transceiver with direction pin;
5 V tolerant; 3-state
74ALVCH32501
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 230
°
C.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| 74ALVCHS162830 | 18-bit to 36-bit address driver with bus hold (3-State) |
| 74ALVCHS162830DGB | 18-bit to 36-bit address driver with bus hold (3-State) |
| 74alvchs16830 | 3-Line To 8-Line Decoders/Demultiplexers 16-PDIP -40 to 85 |
| 74ALVT162240 | 16-bit inverting buffer/driver with 30 Ωtermination resistors (3-State)(帶30 Ω終端電阻器的16位反相緩沖器/驅動器(三態）) |
| 74ALVT162241 | 2.5V/3.3V 16-bit buffer/driver with 30 Ωtermination resistors (3-State)(帶30 Ω終端電阻器的2.5V/3.3V 16位緩沖器/驅動器(三態）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 74ALVCH32501EC,518 | 功能描述:IC UNIV BUS TXRX 26BIT 114LFBGA RoHS:是 類別:集成電路 (IC) >> 邏輯 - 通用總線函數 系列:74ALVCH 產品變化通告:Product Discontinuation 09/Dec/2010 標準包裝:1,500 系列:74AVC 邏輯類型:通用總線驅動器 輸入數:- 電路數:18 位 輸出電流高，低:12mA，12mA 電源電壓:1.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.240"，6.10mm 寬） 供應商設備封裝:56-TSSOP 包裝:帶卷 (TR) |
| 74ALVCH32501EC,551 | 功能描述:IC UNIV BUS TXRX 26BIT 114LFBGA RoHS:是 類別:集成電路 (IC) >> 邏輯 - 通用總線函數 系列:74ALVCH 產品變化通告:Product Discontinuation 09/Dec/2010 標準包裝:1,500 系列:74AVC 邏輯類型:通用總線驅動器 輸入數:- 電路數:18 位 輸出電流高，低:12mA，12mA 電源電壓:1.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.240"，6.10mm 寬） 供應商設備封裝:56-TSSOP 包裝:帶卷 (TR) |
| 74ALVCH32501EC,557 | 功能描述:總線收發器 36-BIT UNIVERSAL BUS TRAN, 3-S RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| 74ALVCH32501ZKFR | 功能描述:通用總線函數 36B Univ Bus Trnscvr RoHS:否 制造商:Texas Instruments 邏輯類型:CMOS 邏輯系列:74VMEH 電路數量:1 開啟電阻（最大值）: 傳播延遲時間:10.1 ns 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大工作溫度:+ 85 C 最小工作溫度:0 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| 74ALVCH32973EC,518 | 功能描述:IC TRANSCVR 16BIT 96LFBGA 制造商:nexperia usa inc. 系列:* 零件狀態:最後搶購 標準包裝:3,500 |
發布緊急采購，3分鐘左右您將得到回復。