Installation of 3M Dual Conductor Remote Input Jack Model 733 a) I" />
鍙冩暩(sh霉)璩囨枡
鍨嬭櫉锛� 724
寤犲晢锛� 3M
鏂囦欢闋佹暩(sh霉)锛� 11/28闋�
鏂囦欢澶�?銆�?/td> 0K
鎻忚堪锛� WORKSTATION MONITOR KIT W/HDWR
妯欐簴鍖呰锛� 1
椤炲瀷锛� 宸ヤ綔绔欑洠(ji膩n)瑕栧櫒
浣跨敤锛� 宸ヤ綔闈�锛岃厱甯讹紙2锛夌洠(ji膩n)瑕�
鐗归粸锛� 閫g簩(x霉)鐩�(ji膩n)瑕栵紝闆欒姱绯荤当(t菕ng)
闆绘簮椤炲瀷锛� AC 閬╅厤鍣�
鍖呮嫭锛� 鐩�(ji膩n)瑕栧櫒 杌熺窔锛屾帴鍦扮窔锛岄洐绾滆姱閬欐帶杓稿叆鎻掑瓟锛孉C 閬╅厤鍣�锛岃鏄庢浉锛屽畨瑁濊灪閲橈紙4锛夛紝闆欑窔閫f帴鍣�
鐩搁棞鐢�(ch菐n)鍝侊細 SCP245-ND - CORD COIL DL R/A 3.4MM PLUG 20'
SCP244-ND - CORD COIL DL R/A 3.4MM PLUG 10'
SCP243-ND - CORD COIL DUAL R/A 3.4MM PLUG 5'
SCP242-ND - CORD COIL DUAL COND GND R/A 20'
SCP241-ND - CORD COIL DUAL COND GND R/A 10'
SCP240-ND - CORD COILED DUAL COND GND R/A 5'
SCP305-ND - KIT VERIFICATION
SCP246-ND - CORD COILED DUAL COND GND 20'
SCP329-ND - KIT REMOTE SPLITTER
SCP234-ND - COILED CORD DUAL COND GND 10'
鏇村...
鍏跺畠鍚嶇ū锛� 98-0798-3713-8
98-0798-3713-8-ND
98079837138
SCP226
19
SECTION 10
Installation of 3M Dual Conductor Remote Input Jack Model 733
a) Insert the plug connector of the Dual
Conductor Remote Input Jack Model
733 cable into the Model 733 jack
at the rear of the 3M Workstation
Monitor Model 724 (Figure 14).
b) Fully insert the small plastic plug
that comes with the kit into the
#2 wrist strap input on the Dual
Conductor Remote Input Jack Model
732. This disables the #2 input and
prevents a situation where two users
would simultaneously attempt to use
the input lines to the Workstation
Monitor Model 724.
c) Position and mount both remote input jacks in convenient locations.
SECTION 11
Verification Procedure for the Workstation Monitor Model 724
The Workstation Monitor Model 724 cannot be recalibrated after the initial
factory calibration. However, the following steps can be used to determine if the
Workstation Monitor Model 724 is operating within its specifications.
Equipment Needed:
Small blade screwdriver.
Resistance Substitution Box (RSB), 1 Ohm to 45 Megohms 卤1%.
One two-conductor cable with standard 3.5 mm (miniature) phone plug
attached on one end and appropriate connectors on the other end to
connect to RSB.
Note: Two-conductor cable must have an isolation resistance of >1 Gigohm
between conductors. Two separated wires may also be used to obtain higherisolation resistance.
Two wires with alligator clips.
Ohmmeter capable of measuring to 45 Megohms 卤0.5%, to verify the RSB.
Figure 14 鈥� Inserting 3M Dual Conductor
Remote Input Jack Model 733 plug into rear of
3M Workstation Monitor Model 724
鐩搁棞PDF璩囨枡
PDF鎻忚堪
725 MONITOR WRIST STRAP DUAL COND
73859 JACKET W/CUFFS TEAL 6XLARGE
741 FOOTPLATE FOR 740 TESTER
746 CERTIFIED WRIST STRAP TESTER AC CERTIFIED
749 PEDESTAL STAND FOR 3M TESTERS
鐩搁棞浠g悊鍟�/鎶€琛撳弮鏁�(sh霉)
鍙冩暩(sh霉)鎻忚堪
72-4 鍔熻兘鎻忚堪:闆绘睜搴�銆侀浕姹犳墸鍜岄浕姹犳帴闋� T-9V-SNAP-4" RoHS:鍚� 鍒堕€犲晢:Eagle Plastic Devices 鐢�(ch菐n)鍝�:Battery Snaps 闆绘睜绲勯浕姹犲ぇ灏�:9 V 闆绘睜鏁�(sh霉)閲�:1 绔帴椤炲瀷:Snaps 椤忚壊:Black 鏉愭枡:Polyvinyl Chloride (PVC) 瀹夎棰ㄦ牸:Snap-In
7-2-4 SCREENED 鍒堕€犲晢:Farnell / Pro-Power 鍔熻兘鎻忚堪:CABLE DEF 7-2-4C 4CORE 500M 鍒堕€犲晢:pro-power 鍔熻兘鎻忚堪:CABLE, DEF 7-2-4C, 4CORE, 500M
7-2-4 SCREENED 鍒堕€犲晢:Farnell / Pro-Power 鍔熻兘鎻忚堪:CABLE DEF 7-2-4C 4 CORE 500M
724 鍒堕€犲晢:3M Electronic Products Division 鍔熻兘鎻忚堪:Static protection 鍒堕€犲晢:CML Innovative Technologies 鍔熻兘鎻忚堪:LAMP MID.FLANGE T1.3/4 6V 1.2W
724 鍒堕€犲晢:SLI EBT 鍔熻兘鎻忚堪:LAMP T1.3/4 MID.FLANGE 6V 1.2W