- 您現在的位置：買賣IC網 > PDF目錄7057 > 66058 (Desco)MAT RUBBER GREEN 24X48" PDF資料下載
參數資料
| 型號： | 66058 |
| 廠商： | Desco |
| 文件頁數： | 2/4頁 |
| 文件大?。?/td> | 0K |
| 描述： | MAT RUBBER GREEN 24X48" |
| 其它有關文件： | Mat Selection Chart |
| MSDS 材料安全數據表： | Statfree T2™ Dual Layer MSDS |
| 標準包裝： | 1 |
| 系列： | Statfree T2™ |
| 墊子類型： | 桌子，工作臺 |
| 形狀： | 矩形 |
| 長度： | 4'（1.22m） |
| 寬： | 2'（0.61m） |
| 厚度： | 0.06" (1.52mm) |
| 顏色： | 綠 |
| 材質： | 橡膠 |
| 特點： | 耗散 |
| 包括： | 接地軟線，接地卡扣套件 |
TB-2000 Page 2 of 4
Grounding Methods
Method 1 (Grounding via ground cords)
1. Desco recommends using a common point ground cord when
grounding via ground cords. Most common point ground cords
will ground your ESD worksurface and provide banana jack
ground points for two wrist straps.
2. A common point ground should be installed at each workstation
and should be connected directly to a verified “green wire”
equipment ground. Only one groundable point should exist on a
worksurface.
Figure 5. Common point ground for each workstation.
3. Wrist straps should never be grounded through a worksurface,
as the added resistance of the worksurface material will
prevent the wrist strap from operating properly.
Figure 6. Proper grounding of wrist straps.
4. Per ANSI/ESD S1.1, a current limiting resistor in the wrist strap
ground cord is recommended. If other than a one megohm
resistor, special marking in red is required.
For additional information on grounding we recommend Desco
Technical Bulletin TB-2007.
Groundable Point Installation
1. Before installing a groundable point on your mat you must first
determine whether you will need a snap socket or stud, the
type of snap hardware and the location.
2. Desco has three types of 10mm (.395") field installable mat
grounding snaps. The first type is a screw-on snap kit Desco
item number 09864 Universal Snap Kit.
A. Determine the position of the grounding snap (one only
per mat) and type of fastener you will be installing (socket
or stud). Take precautions not to cut your hand, and punch
a hole through the material with a small Phillips screwdriver
or awl.
B. Remove the release paper from the circular common point
ground label and affix it so that it aligns with the hole on the
material.
C. Select one of the screws as follows:
Material less than .100" thick - short screw
Material greater than .100" thick - long screw
D. Insert the screw through the top on the snap stud or socket,
the washer, the label and the material. Affix the assembly
with the conical nut supplied with the kit and tighten down
the screw using a Phillips screwdriver.
E. Remaining will be either a 10mm stud or socket, and either
a long or short screw to be discarded or saved for another
application.
ASSEMBLE
SCREW, STUD,
WASHER, LABEL
AND CONICAL NUT
AS SHOWN
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST - One Colgate Way
, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
WRONG!
RIGHT!
Figure 8. Installing Universal Snap Kit on mat.
USE A PHILLIPS
SCREWDRIVER OR
AWL TO PUNCH
A HOLE IN THE
MATERIAL
2012 DESCO INDUSTRIES INC.
Employee Owned
Figure 7. Three kinds of snaps.
3. The second type of mat grounding snap is the push and
clinch snap. This snap is designed for use with any type of
soft mat material: dissipative, conductive or multi-layered. It is
recommended for use with three-layered material, because it
provides excellent contact with the internal conductive scrim
layer. It is recommended that before inserting this snap, the
mat be punctured with a sharp tool where the snap will be
placed. Take precautions not to cut your hand. Push and Clinch
snaps are available as a snap stud as item #09861 and as a
snap socket as item #09863.
A. Remove the release paper from the circular label and
affix it onto the mat material in the desired location.
B. Center the prongs on the snap assembly with the label.
Apply pressure to the snap until the prongs come through
the back of the mat, then clinch over prongs to secure snap
as shown in Figure 9.
相關PDF資料 |
PDF描述 |
|---|---|
| L37-3-11-11-1 | THERMAL PAD L37-3 11X11X1MM |
| 433102-23-0 | TERM BARRIER 23CIRC 1 ROW .4375 |
| 431513-21-0 | TERM BARRIER 21CIRC 1 ROW .4375 |
| 431512-21-0 | TERM BARRIER 21CIRC 1 ROW .4375 |
| 431413-21-0 | TERM BARRIER 21CIRC 1 ROW .4375 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 66058-001 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| 66058-002 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| 6605801-1 | 功能描述:以太網和電信連接器 1X1 MAG45(TM)7H2 P1, 766, CAP RoHS:否 制造商:Pulse 產品:Modular Jacks 性能類別: USOC 代碼:RJ45 位置/觸點數量: 安裝風格:Through Hole 端口數量:1 x 1 型式:Female 屏蔽: 電流額定值: 電壓額定值: 觸點電鍍: 外殼材料:Thermoplastic IP 等級: |
| 6605807-2 | 制造商:TE Connectivity 功能描述:CONN TEL/TELC F 8 POS 2.54MM RA TH 8TERM - Trays 制造商:TE Connectivity 功能描述:Integrated Magnetic, Stacked (Mag45?) and Power over Ethernet (PoE) |
| 6605808-1 | 制造商:TRP CONNECTOR LTD. 功能描述:1X1 MAG45 10/100 POE 7D15 G/Y LED NO TAB - Trays |
發布緊急采購，3分鐘左右您將得到回復。