- 您現在的位置：買賣IC網 > PDF目錄360280 > 5962R9858301QXC (Aeroflex Inc.) 20MHz 16-bit Microcontroller PDF資料下載
參數資料
| 型號： | 5962R9858301QXC |
| 廠商： | Aeroflex Inc. |
| 英文描述： | 20MHz 16-bit Microcontroller |
| 中文描述： | 20MHz的16位微控制器 |
| 文件頁數： | 15/43頁 |
| 文件大?。?/td> | 186K |
| 代理商： | 5962R9858301QXC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
15
15
TI
P2.2
---
Port 2 Pin 2. An input only port pin that is written at location
10h of HWindow 0. P2.2 will always generate EXTINT1
(INT13, 203Ah) unless masked by the INT_MASK1 register.
Assert EXTINT1 for at least 2 state times to guarantee acknowl-
edgment by the interrupt controller.
TI
EXTINT
High
External Interrupt. Setting IOC1.1 = 0 enables pin 15 as the
source for the external interrupt EXTINT. A rising edge on this
pin will generate EXTINT (INT07, 200Eh). Assert EXTINT for
at least 2 state times to ensure acknowledgment by the interrupt
controller.
During Power Down mode, asserting EXTINT places the chip
back into normal operation, even if EXTINT is masked.
16
TUBS
RESET
Low
Master Reset. The first external reset signal supplied to the
UT80CRH196KD must be active for at least 16 state times. All
subsequent RESET assertions need only be active for 1 state
time because the UT80CRH196KD will continue driving the
RESET signal for an additional 16 state times. See section 1.1.2
for more information on the RESET function of the
UT80CRH196KD.
17
TI
P2.1
---
Port 2 Pin 1. An input only port pin that is read at location 10h
of HWindow 0.
Setting SPCON.3 = 0 enables the P2.1 function of pin 17.
TB
RXD
---
RXD is a bidirectional serial data port. When operating in Serial
Modes 1, 2, and 3, RXD receives serial data. When using Serial
Mode 0, RXD operates as an input and an open-drain output for
data.
Setting SPCON.3 = 1 enables the RXD function of pin 17.
18
2
TUO
P2.0
---
Port 2 Pin 0. An output only port pin that is written at location
10h of HWindow 0.
Setting IOC1.5 = 0 enables the P2.0 function of pin 18.
TUO
TXD
---
Transmit Serial Data (TXD). When set to Serial Mode 1, 2, or 3,
TXD transmits serial port data. When using Serial Mode 0,
TXD is used as the Serial Clock output.
Setting IOC1.5 = 1 enables the TXD function of pin 18.
TUI
ICT
Low
In-Circuit Test. The UT80CRH196KD will enter the In-Circuit
Test mode if this pin is held low during the rising edge of
RESET.
Table 10: 68-lead Flat Pack Pin Descriptions
QFP Pin#
I/O
Name
Active
Description
相關PDF資料 |
PDF描述 |
|---|---|
| 5962R9858301QXX | 20MHz 16-bit Microcontroller |
| 5962R9858301QXXC | 20MHz 16-bit Microcontroller |
| 5962R9858301VXC | 20MHz 16-bit Microcontroller |
| 5962R9858301VXX | 20MHz 16-bit Microcontroller |
| 5962R9858301VXXA | 20MHz 16-bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962R9863601VGA | 制造商:Analog Devices 功能描述: |
| 5962R9863602VGA | 制造商:Analog Devices 功能描述:OP AMP, JFET-INPUT - Rail/Tube |
| 5962R9863701VGA | 制造商:Analog Devices 功能描述:- Rail/Tube |
| 5962R9863701VHA | 制造商:Analog Devices 功能描述:AEROSPACE LOW INPUT CURRENT OPERATIONAL AMPLIFIER - Rail/Tube |
| 5962R9863701VPA | 制造商:Analog Devices 功能描述:OP AMP, GENERAL PURPOSE - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。