參數資料
型號: 4280
英文描述: Low-Cost, 2.7V to 5.5V Temperature Switches in a SOT23
中文描述: 4280組數據表數據表630K/JUN.11.99
文件頁數: 8/48頁
文件大?。?/td> 630K
代理商: 4280
7
MITSUBISHI MICROCOMPUTERS
4280 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS
Fig. 5 Stack registers (SKs) structure
Fig. 6 Example of operation at subroutine call
SK
0
SK
1
SK
2
SK
3
(SP) = 0
(SP) = 1
(SP) = 2
(SP) = 3
Program counter (PC)
Executing RT
instruction
Executing BM
instruction
Stack pointer (SP) points “3” at reset or
returning from RAM back-up mode. It points “0”
by executing the first BM instruction, and the
contents of program counter is stored in SK
0
.
When the BM instruction is executed after four
stack registers are used ((SP) = 3), (SP) = 0
and the contents of SK
0
is destroyed.
Returning to the BM instruction execution
address with the RT instruction, and the BM
instruction is equivalent to the NOP instruction.
(SP)
(SK
0
)
(PC)
0
0001
16
SUB1
Main program
0002
16
NOP
Address
0000
16
NOP
0001
16
BM SUB1
Subroutine
SUB1 :
NOP
·
·
RT
(PC)
(SP)
(SK
0
)
3
·
Note:
(5) Most significant ROM code reference enable flag (URS)
URS flag controls whether to refer to the contents of the most
significant 1 bit (bit 8) of ROM code when executing the TABP
p instruction. If URS flag is “0,” the contents of the most
significant 1 bit of ROM code is not referred even when
executing the TABP p instruction. However, if URS flag is “1,”
the contents of the most significant 1 bit of ROM code is set to
flag CY when executing the TABP p instruction (Figure 4).
URS flag is “0” after system is released from reset and returned
from RAM back-up mode. It can be set to “1” with the URSC
instruction, but cannot be cleared to “0.”
(6) Stack registers (SKs) and stack pointer (SP)
Stack registers (SKs) are used to temporarily store the contents
of program counter (PC) just before branching until returning
to the original routine when;
performing a subroutine call, or
executing the table reference instruction (TABP p).
Stack registers (SKs) are four identical registers, so that
subroutines can be nested up to 4 levels. However, one of
stack registers is used when executing a table reference
instruction. Accordingly, be careful not to over the stack. The
contents of registers SKs are destroyed when 4 levels are
exceeded.
The register SK nesting level is pointed automatically by 2-bit
stack pointer (SP).
Figure 5 shows the stack registers (SKs) structure.
Figure 6 shows the example of operation at subroutine call.
(7) Skip flag
Skip flag controls skip decision for the conditional skip
instructions and continuous described skip instructions.
Note : The 4280 Group just invalidates the next instruction
when a skip is performed. The contents of program
counter is not increased by 2. Accordingly, the number
of cycles does not change even if skip is not performed.
However, the cycle count becomes “1” if the TABP p,
RT, or RTS instruction is skipped.
相關PDF資料
PDF描述
42816-0212 Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
42816-0312 Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
42816-0412 Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
42816-0512 Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
42816-0612 Low-Cost, 2.7V to 5.5V, Analog Temperature Sensor Switches in a SOT23
相關代理商/技術參數
參數描述
4-280 制造商:Raaco 功能描述:
4-280 ESD 制造商:Raaco 功能描述:
42-800 制造商:Distributed By MCM 功能描述:Flat Belt
4280-00 功能描述:KIT EVAL FOR 4280 RF SWITCH RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發(fā)套件,板 系列:UltraCMOS™ 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796
4280000 制造商:BERNSTEIN 功能描述:BOX GRP IP65 EEXE GREY