參數資料
型號： 3386H-1-504
英文描述： TRIMMER 11MM CERMET EIN 500K 300V 0.5W
中文描述： 修邊機11毫米艾因500K的300V金屬陶瓷為0.5W
文件頁數： 80/86頁
文件大?。?/td> 3230K
代理商： 3386H-1-504
Specifications are subject to change without notice.
84
This application note is designed to provide step-by-step
processing recommendations. It covers the popular SMC
soldering processes currently in use and provides recommenda-
tions and cautions for each step. Since many variations of
temperature, time, processes, cleaning agents and board types
are found in the electronics industry, you’ll want to test and
verify your own system.
The process steps, recommendations and cautions are
based on Bourns Trimpot surveys of SMC users, equipment
manufacturers and materials suppliers. Also, comments
reflect results of Bourns’ testing. Our findings suggest the
following soldering and cleaning processes:
1. SOLDERING - Forced Hot Air, Convection, IR, Vapor Phase
(In-Line), Wave (Single and Dual)
2. CLEANING - Solvent, Aqueous, Semi-Aqueous, No-Clean
On the facing page are the common methods, materials and
maximum temperature/time parameters for soldering and
cleaning processes.
1
Solder Paste
Printing
Reflow
GENERAL
Use the optimum
solder paste for the
pattern, printing
process, solder paste
density and solder
joint quality.
RECOMMENDED
Use Sn 63% Pb 37%
solder paste. Use 8 to
10 mil thickness for
solder paste print.
CAUTION
Since solder paste
usually contains a high
percentage of activators,
you must ensure
adequate cleaning to
remove all residues,
unless no-clean (low
solids) paste is used.
Adhesive
Application
Flow (Wave)
GENERAL
The adhesive must hold
the SM Component
(SMC) in correct
orientation upon place-
ment and maintain
correct trimmer position
during physical
handling before final
solder processing.
RECOMMENDED
To assure positional
stability, place a single
dot of epoxy under the
SMC.
CAUTION
Stability after placement
is a direct function of
the volume of adhesive
used. Use enough epoxy
to assure stability
through the cure
process.
Avoid overflow of epoxy
to solder pad and
terminal areas.
Adhesive
Cure
Flow (Wave)
GENERAL
Use heat/time cure
method with either
convection oven or
infrared radiation.
RECOMMENDED
Cure using the
temperature and
times recommended
by the adhesive
manufacturer.
CAUTION
Use enough cure
time to assure
complete adhesive
transition from fluid
to solid.
Flux
Application
Flow (Wave)
GENERAL
Use the correct flux
to remove surface
oxides, prevent
reoxidation and
promote wetting.
RECOMMENDED
RMA
No-clean SRB
(Synthetic resin
based)
OA (Organic Acid)
(See caution)
CAUTION
Avoid highly
activated fluxes.
Consult factory before
using OA.
SMC
Placement
GENERAL
Use pick-and-place
equipment with
vacuum nozzle ID size
that allows adequate
suction to pick the
SMC out of the
embossed cavity.
RECOMMENDED
The nozzle inside
diameter (ID) should
not exceed .100 in.
(2.54mm) to ensure
adequate suction and
part alignment.
CAUTION
Assure parts are
placed so that all
terminals are
equidistant (<4 mils)
from the solder pads.
Align terminals with
solder belt direction of
travel to avoid body
shadowing effects
during flow soldering.
EPOXY
Soldering And Cleaning Processes
相關PDF資料
PDF描述
322CNQ030 300 Amp Schottky Rectifier(300 A 肖特基整流器)
3239-00 2.2 GHz Integer-N PLL for Low Phase Noise Applications
323GT 5.0mm Round Type LED Lamps
3245A-MSOP8 Constant Current Forward/Reverse Driver IC for Digital Cameras
3250 Square Trimming Potentiometer
相關代理商/技術參數
參數描述
3386H-1-504LF 功能描述:微調電阻 - 通孔 3/8" 500Kohms 10% 0.5Watts Square RoHS:否 制造商:Vishay/Sfernice 產品:Trimmer Resistors - Multi Turn 產品類型:Multiturn 轉數:14 錐度:Linear 電阻:10 kOhms 電壓額定值:250 V 端接類型:Pin 功率額定值:250 mW (1/4 W) 容差:10 % 溫度系數:100 PPM / C
3386H-1-504LF 制造商:Bourns Inc 功能描述:RESISTORS CERMET VARIABLE ROTARY (POTEN
3386H-1-504T 功能描述:微調電阻 - 通孔 3/8"SQ 500KOHMS 10% 0.5WATTS RoHS:否 制造商:Vishay/Sfernice 產品:Trimmer Resistors - Multi Turn 產品類型:Multiturn 轉數:14 錐度:Linear 電阻:10 kOhms 電壓額定值:250 V 端接類型:Pin 功率額定值:250 mW (1/4 W) 容差:10 % 溫度系數:100 PPM / C
3386H-1-504TLF 功能描述:微調電阻 - 通孔 3/8" 500Kohms 10% 0.5Watts Square RoHS:否 制造商:Vishay/Sfernice 產品:Trimmer Resistors - Multi Turn 產品類型:Multiturn 轉數:14 錐度:Linear 電阻:10 kOhms 電壓額定值:250 V 端接類型:Pin 功率額定值:250 mW (1/4 W) 容差:10 % 溫度系數:100 PPM / C
3386H-1-505 功能描述:微調電阻 - 通孔 3/8"SQ 5MOHMS 10% 0.5WATTS RoHS:否 制造商:Vishay/Sfernice 產品:Trimmer Resistors - Multi Turn 產品類型:Multiturn 轉數:14 錐度:Linear 電阻:10 kOhms 電壓額定值:250 V 端接類型:Pin 功率額定值:250 mW (1/4 W) 容差:10 % 溫度系數:100 PPM / C
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*