- 您現在的位置：買賣IC網 > PDF目錄371434 > 28F001BX-T (Intel Corp.) 1-MBIT (128K x 8) BOOT BLOCK FLASH MEMORY PDF資料下載
參數資料
| 型號： | 28F001BX-T |
| 廠商： | Intel Corp. |
| 英文描述： | 1-MBIT (128K x 8) BOOT BLOCK FLASH MEMORY |
| 中文描述： | 1兆位（128K的× 8）引導塊閃存 |
| 文件頁數： | 12/33頁 |
| 文件大?。?/td> | 436K |
| 代理商： | 28F001BX-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
28F001BX-T/28F001BX-B
BOOT BLOCK PROGRAM AND
ERASE
The boot block is intended to contain secure code
which will minimally bring up a system and control
programming and erase of other blocks of the de-
vice, if needed. Therefore, additional ‘‘lockout’’ pro-
tection is provided to guarantee data integrity. Boot
block program and erase operations are enabled
through high voltage V
HH
on either RP
Y
or OE
Y
,
and the normal program and erase command se-
quences are used. Reference the AC Waveforms for
Program/Erase.
If boot block program or erase is attempted while
RP
Y
is at V
IH
, either the Program Status or Erase
Status bit will be set to ‘‘1’’, reflective of the opera-
tion being attempted and indicating boot block lock.
Program/erase attempts while V
IH
k
RP
Y
k
V
HH
produce spurious results and should not be attempt-
ed.
In-System Operation
For on-board programming, the RP
Y
pin is the most
convenient means of altering the boot block. Before
issuing Program or Erase confirms commands, RP
Y
must transition to V
HH
. Hold RP
Y
at this high volt-
age throughout the program or erase interval (until
after Status Register confirm of successful comple-
tion). At this time, it can return to V
IH
or V
IL
.
290406–7
Bus
Command
Comments
Operation
Write
Program
Setup
Data
e
40H
Address
e
Byte to be
Programmed
Write
Program
Data to be programmed
Address
e
Byte to be
Programmed
Read
Status Register Data.
Toggle OE
Y
or CE
Y
to
update Status Register
Check SR.7
1
e
Ready, 0
e
Busy
Standby
Repeat for subsequent bytes.
Full status check can be done after each byte or after a
sequence of bytes.
Write FFH after the last byte programming operation to
reset the device to Read Array Mode.
Bus
Command
Comments
Operation
Standby
Check SR.3
1
e
V
PP
Low Detect
Standby
Check SR.4
1
e
Byte Program Error
SR.3 MUST be cleared, if set during a program attempt,
before further attempts are allowed by the Write State
Machine.
SR.4 is only cleared by the Clear Status Register
Command, in cases where multiple bytes are
programmed before full status is checked.
If error is detected, clear the Status Register before
attempting retry or other error recovery.
Figure 9. 28F001BX Byte Programming Flowchart
12
相關PDF資料 |
PDF描述 |
|---|---|
| 28F001BX | 5 V Boot Block Flash Memory(5 V引導塊閃速存儲器) |
| 28F002BC | 28F002BC 2-MBIT (256K X 8) BOOT BLOCK FLASH MEMORY |
| 28F002BV-B | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F004B3 | 3 Volt Advanced Boot Block Flash Memory(3 V,4M位高級引導塊閃速存儲器) |
| 28F004S3 | BYTE-WIDE SMART 3 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F001BX-T/28F001BX-B/28F001BN-T/BN-B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:28F001BX-T/28F001BX-B/28F001BN-T/BN-B |
| 28F001BX-T/B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:28F001BX-T/B |
| 28F002BC | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:28F002BC 2-MBIT (256K X 8) BOOT BLOCK FLASH MEMORY |
| 28F002BL-B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2-MBIT (128K x 16. 256K x 8) LOW-POWER BOOT BLOCK FLASH MEMORY FAMILY |
| 28F002BL-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2-MBIT (128K x 16. 256K x 8) LOW-POWER BOOT BLOCK FLASH MEMORY FAMILY |
發布緊急采購，3分鐘左右您將得到回復。